Check motor spare and replace motor ( AGUS & ADI & MUHAIMIN )

Re check cycle mode result function ok. Do survey way of pulling cable ( RIZAL & EVE RIZALDI & ANDRI )

Add grease at LS motor 25 times ( EDI & EVE HADIF & DADANG )

Check recondition motor ( AGUS & ADI & MUHAIMIN )

Service speed motor result ok ( AGUS & ADI & MUHAIMIN )

Clean up area motor and filter motor. Measure vibration-noise-temperature for  FS and LS. Add grease 20 times-25 times and 30 times for FS and LS ( EDI & EVE HADIF & DADANG )

Install motor at CKD do test run motor result found there is friction at motor when installing  ( AGUS & MUHAIMIN & ANDRI & DADANG )

Measure heat at winding L63 MD1, result around 70 degree celcius and body around 58.5 to 64.2 degree celcius. Advise install exhause fan to take out heat at terminal cable to prevent motor function well ( AGUS & ADI & MUHAIMIN & DADANG & JAJAT )

Check cable sensor at ware house, result found cable 6P x 1.5 mm. Take cable from ware house bring to ER6 ( ADI & MUHAIMIN & DADANG )

Clean up probe-sample line-filter sample line-diaphragm pump-fiter balston-dryer gas pump from dirty of dust. Check function humidity sensor and filter humidity result function humidity normal and filter humidity normal ( RIZAL & EVE AKPAN & ANDRI )

Do update wiring for L1C TR1 ( AGUS )

Replace bearing motor of CKD at workshop ( MUHAIMIN & EDI )

Do prepare for Audit Safety like SWP and HIRAC ( JAJAT & ADI )

Repare handle panel I/O fail result function handle ok ( ANDRI & DADANG )

Do replace CI830 to CI801 test ON LINE ok ( AGUS & EVE AKPAN )

Do test run after reposition blade motor. Measure ampere for R-S-T result 58.4 ampere to 60.4 ampere also measure vibration result 3.4 mm/s and 2.6 mm/s ( EDI & MUHAIMIN )

Replace pump at HRG. Test function ok ( RIZAL & ANDRI )

Do Support area NR1 for concern feeding ( JAJAT & AGUS & RIZAL & ADI & MUHAIMIN & ANDRI & DADANG & AIMAN  & EVE AKPAN )

Replace limit switch for bucket elevator test function result ok. Adjust position of sensor more deep that before, test run bucket elevator result ok normal ( ADI & MUHAIMIN & EVE AKPAN & AGUS & EDI & RIZAL )

Decreasing  break. test function winci result ok ( EDI & MUHAIMIN & DADANG )

Repare tubing for sample pressure  at cyclone 2. Do extend pipe draft of sample line pressure at cyclone 4 result ok ( RIZAL & ANDRI )

Replace membran bag filter 6 units test function bag filter result normal ( EDI & DADANG )

Test run motor result function normal.  AGUS & MUHAIMIN ) Because size of blade different

Do inspection electrical tools of PT Pincuran Mas, total 38 units tagging with blue color ( ADI & EVE AKPAN )

Inspection electrical tools of PT Pincuran Mas, 1 portable lamp. Tagging with blue color ( ADI & EVE AKPAN )

Do completing data check sheet for PMR service analyzer L63 2K1 - L63 2K2 - L63 2K3 - 483 2K1 - 463 2K1 - 443 2K1 - 423 2K1 for 1st weeks of september 2025 ( ADI & EVE AKPAN )

Dismantle motor CKD. Bring to workshop inspection motor result good condition. Install back motor at workshop continue connected at local ( AGUS )

Install motor at location. Test run motor, measure ampere result: 6.04 A - 5.77 A - 5.73 A, vibartion and noise for FS and LS result: 3.04 mm/s 0.92 gE; 2.7 mm/s 1.67 gE. Test function of bag filter result normal ( MUHAIMIN & EVE AKPAN & DADANG )

Restart computer, check program. Tripper still can not AUTO ( RIZAL & AGUS & ANDRI )

Dismantle Dismantle motor found bearing motor 6206 bad condition. Replace bearing motor with spare install ( EDI & MUHAIMIN & DADANG )

Clean up panel I/O LC1-2RA 71, LC1-2RA 41, LC1-2RA 11, 4C2-2RC 22, 4C2-2RC 21, 4C2-2RC 11, 4C2-2RC 23, 4C2-2RC 24 from dirty of dust and coal use blower ( ADI & EVE AKPAN )

Check at location, motor hoist need scafolding to check. Measure use Meger, found grounded between line R-S-T to grounded ( EDI & ADI )

Do install battery UPS of ER4 ( JAJAT & AGUS & RIZAL & ADI & AIMAN & ANDRI & MUHAIMIN & ANDRI & DADANG )

Do pulling cable data 6P x 0.75 x 3  ER 3 ( @25m ) + Install Module DI  ( JAJAT & RIZAL & AGUS & MUHAIMIN & ANDRI & DADANG )

Do support manuver power at ER3 - ER4 and ER5 ( JAJAT & AGUS & RIZAL & ADI & ANDRI & MUHAIMIN & DADANG & AIMAN )

Pulling cable of winding CM. Cable already at  Motor  L63-MD1 dan IO ER 4. Connected cable at motor at panel I/O ER4 ( AGUS & RIZAL & MUHAIIMIN & ANDRI & DADANG & JAJAT )

Inspection electrical and welding tools of RMP total 40 units tagging blue color. Note 1 mixer is not safe because not full fill requirement safety of PT SBI tagging can not use ( ADI & JAJAT )

Automation : Replace PS dan CI830,  di NL1.1. 3 , add module AI830---- Online (Normal) ( JAJAT & RIZAL )

Clean up area motor - filter motor - carbon bursh room from dirty of dust from dirty of dust. Measure actual long every carbon brush found long carbon brush1: 38.89 cm 2: 38.73 cm 3: 34.10 cm 5:39.82 cm 6: 31.83 cm7 cm: 46.41 cm  8: 43.60 cm 9: 45.54 cm 10: 45.24 cm 11: 43.85 cm 12: 40.34 cm 13: 33.86 cm 14: 28.88 cm 15: 33.28 cm 16: 42.97 cm 18: 25.78 cm 19: 36.46 cm 20: 39.92 cm 21: 40.03 cm 22: 34.70 cm 23: 43.82 cm 24: 43.90 cm. Replace carbon brush 3-6-13-14-15-18-22 with spare carbon brush ( EDI & ADI )

Do clean up panel I/O at east and west blending from dirty of dust use hand blower also clean up panel pfister feeder. Also clean up panel I/O area water pump and area raw mill & coal mill for HS from dirty of coal use hand blower. Clean up panel I/O area feed bin and pre heater from 8th floor to 2nd floor ( ADI & EVE TEGAR )

Do replace CI 801 2 each at N31 and replace module I/O at N41 Bus A ( RIZAL & ANDRI )

Take motor spare from warehouse bring to location. Install motor spare and do connection cable power. Do function test motor with every speed and measure vibration and noise for FS and LS motor ( AGUS & EDI & JAJAT & MUHAIMIN & DADANG )

Do support black out at ER3 - ER4 and ER5 ( JAJAT & AGUS & RIZAL & ADI & MUHAIMIN & ANDRI & AIMAN & DADANG )

Take out spare CEMS from cabinet 25 and put at special cabinet and also YM CEMS. Add spare part MC at cabinet 68 file spare part of ws electric nr1 ( JAJAT & ADI )

Final drawing of electrical  and do observation pulling cable from L1C TR1 to ER6 ( AGUS )

Clean up flange probe - sample line - filter sample - diaphragm pump - filter balston - dryer gas pump from dirty of coal. Check humidity sensor function and filter humidity, result function sensor humidity normal and filter humidity still ok ( MUHAIMIN & ANDRI )

Clean up flange, probe, sample line, filter probe, diaphragm pump, dryer gas pump, filter balston from dirty of dust. Check humidity sensor function and filter humidity, result function sensor normal and filter humidity good condition ( EDI & EVE TEGAR & DADANG )

Make data file spare part cabinet 7 -  cabinet 9 - cabinet 47 also add spare part at cabinet 25 cabinet 61. Safe file at PC as spare part of ws electric nr1 ( JAJAT & ADI )

Clean up area motor and filter motor. Measure vibration-noise-temperature for FS and LS. Add grease 20 times-25 times-35 times for FS and LS motor ( EDI & EVE TEGAR )

Check at location found cable motor brake short, repare cable and do test function motor brake result ok ( AGUS & MUHAIMIN & ANDRI & DADANG )

Complete data TPM of ER4 bottom floor, print out, take sign of people joint TPM install at dash board TPM ( RIZAL )

Clean up flange probe - sample line - filter sample line - diaphragm pump -  filter balston - dryer gas pump from dirty of coal. Check humidity sensor function and filter sensor, result function sensor good and filter sensor good condition ( RIZAL, EVE TEGAR, ANDRI )

Labelling  for SX, MS, MX and do test signal from local to I/O panel result ok ( AGUS, EDI, MUHAIMIN, DADANG )

Clean up MCC ER3 and ER4 top also bottom from dirty dust use brush and mop room ( DIVA )

Complete data check sheet for PMR critical motor for 25-8-25 also make notification for job . Make template safety and print out template ER4. Make data file spare part cabinet 8 - cabinet 9 ( JAJAT, ADI )

Make data spare part cabinet 74 - cabinet 75 safe at PC as spare part of work shop nr1. Complete data check PMR analyser L63 2K1-L63 2K2-L63 2K3-483 2K1-463 2K1-443 2K1-423 2K1, PMR camera burner-pyrometer-IR TAD-t scanner-hoist crane-critical motor RM KL CM CC. Also WBI bottom blending,KL,CC,clinker silo-top blending,CT,PH,KL-feed bin,RM,CT,dust transport-CM,truck lift, bc transport, tripper, reclaimer coal-panel lighting & welding ( JAJAT, ADI, EVE TEGAR )

Make cover motor at work shop for area 393 ( EDI, MUHAIMIN , DADANG )

Do labeling for SX - MS - MX. Also install labelling at cable signal. Test signal from local to I/O panel result signal ok ( AGUS, EDI, MUHAIMIN, DADANG )

Clean up flange probe - probe - filter sample line - sample line - diaphragm pump - filter balston - dryer gas pump from dirty of dust. Check humidity sensor function and filter humidity, result function sensor normal and filter good condition ( RIZAL 

Make data spare part cabinet 69 - cabinet 73 safe at PC as spare part of work shop nr1 ( JAJAT & ADI )

Motor stuck, wire broken (Waiting  new ones) ( RIZAL & JAJAT & ANDRI )

Replace battery AUTO Grease for 393 BE1 & 433 BE1

Do wiring cable I/O at ER6, check signal from local to I/O result ok ( JAJAT, EDI, RIZAL, ADI, MUHAIMIN, ANDRI, DADANG )

Do install lighting lamp at tail pulley. Test function result ok lighting lamp on ( RIZAL & ANDRI )

 Do replace bearing motor bogie number of bearing 6307. Test motor no load result normal for RST |  ( MUHAIMIN, EVE TEGAR & DADANG )

Make data spare part cabinet 62 - cabinet 63 - cabinet 68, safe at PC as spare part of work shop nr1 ( JAJAT & ADI )

Install sign safety for EVACUATION ROUTE 6 each and cleaning tool 2 each at TPM ER4 ( ADI )

Prepare cover motor for area 393  ( EDI & MUHAIMIN & ANDRI & DADANG )

Replace  relay, monitor function purging analyser ( RIZAL )

Replace receptacle, test function result ok ( MUHAIMIN & ANDRI )

Replace lighting lamp with spare, test on result lighting lamp on ( EDI & DADANG )

Replace vibration sensor, result reading vibration back normal ( RIZAL & ANDRI & EVE FAJAR )

Make data spare part cabinet 56 - cabinet 58 - cabinet 61, safe at PC as spare part of work shop nr1 ( JAJAT & ADI )

Clean area motor and filter motor. Measure vibration-noise-temperature FS and LS motor. Add grease motor 25 times-30 times-35 times for FS and LS motor ( MUHAIMIN & DADANG )

Clean up filter sample line and solenoid valve. Result reading analyser ok ( RIZAL & ANDRI )

Check DC ampere at HRG and ER6 wiring connection I/O ( JAJAT & EVE TEGAR )

Clean area motor and filter motor. Measure vibration-noise-temperature FS and LS motor. Add grease motor 25 times-30 times-35 times for FS and LS motor ( MUHAIMIN & DADANG )

Do resetting PPM at sensor miltronics. Result function ok ( EDI )

Do prepare print out HAC for L1C TR1. Also install HAC at location ( AGUS & MUHAIMIN & JAJAT & RIZAL & ANDRI & DADANG & EVE HADIF & EDI & ADI )

Do fabrication cover motor for area 393 RF1 ( ANDRI & DADANG )

Replace relay and service sample pump replace connector tube at sample pump. Service s/v 3 way for release pressure after purging found dirty inside. After clean up 3 times purging reading O2 normal ( RIZAL & EDI )

Make data file for cabinet 49 - cabinet 50 - cabinet 54 - cabinet 55 - cabinet 73 safe file as spare part ws electric Nr1  also move every file to this name of spare part ws electric Nr1 ( JAJAT & ADI & EVE HADIF )

Clean area ER4 bottom area from dirty dust use broom, also vacuum cleaner. Update data TPM at dash board ( JAJAT & RIZAL & AGUS & EDI & ADI & MUHAIIMIN & TRUBA JAGA CIPTA & ANDRI & DADANG & EVE HADIF )

Make data spare part cabinet 67 - cabinet 73. Safe file as satelit part electric kiln form at personal computer as 21-8-25 ( JAJAT & ADI )

List consumable part include number item every part ( AGUS & RIZAL )

Do adjust probe sensor and service card speed sensor. Result ok ( EDI & ANDRI & DADANG )

Do service indication local stop at L33 BF1, test function result ok ( EDI & ANDRI & DADANG )

Clean up flange probe, sample line, filter sample line, diaphragm pump, filter balston, dryer gas pump from dirty of dust coal. Check humidity sensor and filter sensor, result function sensor ok and filter still good condition ( MUHAIMIN & EVE HADIF )

Make data spare part cabinet 79 - cabinet 80 - cabinet 81. Safe file as satelit part electric kiln form at personal computer as 20-8-25. Also put spare part outside of electric at cabinet 22 - cabinet 51 - cabinet 67 - cabinet 73 and add additional spare part at file  ( JAJAT & ADI )

Do top up AUTO grease L1C BC5 and cleaning control and radio link use hand blower ( MUHAIMIN & ANDRI )

Do fabrication LCS for L1C BC1 and L1C BC3 also prepare accecories for LCS ( AGUS & DADANG )

Clean flange probe-probe-sample line-filter sample line-diaphragm pump-filter balston-dryer gas pump from dirty of dust. Check humidity sensor and filter sensor, result function sensor humidity and filter ok ( RIZAL & EVE HADIF )

Install lighting lamp for head pulley, replace timer for lighting lamp. Test on function of lighting lamp result ok ( ADI & ANDRI & DADANG )

Clean up filter cooling fan, found filter very dirty ( AGUS & EVE HADIF )

Clean up purge air unit motor and  filter purge air unit- flange with tube dust hunter- swivel window transciever / recieve also reflector-alignment dust hunter- transducer A & B - CEMS room also gas CEMS room - filter cabinet MCS 100 E from dust ( RIZAL & EVE FAJAR )

Clean area motor and filter motor. Measure vibration-noise-temperature FS and LS motor. Add grease 25 times-30 times for LS and FS motor ( AGUS & DADANG )

Clean area motor and filter motor. Measure vibration-noise-temperature FS and LS motor. Add grease 25 times-30 times for LS and FS motor ( MUHAIMIN & ANDRI )

Bring cable from ER3 to location, pulling 3 line cable from motor dumping coal truck to ER6 ( JAJAT & AGUS &  & EDI &RIZAL & ADI &  MUHAIMIN & DADANG & AIMAN )

Cleaning Motor and replace CB no 12 with spare ( MUHAIMIN & ANDRI & DADANG )

Make data spare part Cabinet 67 - Cabinet 68 and safe file at computer as Satelit Electric Kiln Form 15-8-25 ( JAJAT & ADI )

Do dismantling battery ex UPS ER3 bring to scrap chemical and cleaning motor area 423 BF1 ( MUHAIMIN & ANDRI & AIMAN & DADANG )

Do put signal pulse tonase and total tonase for tripper to CCR and upload HMI to factory talk ( RIZAL )

Do drawing electrical for area truck lift save file at computer ( AGUS )

Do WBI Electric & Ins & Check I/O Feed Bin and cleaning use hand blower I/O module ( EDI & EVE FAJAR )

Take observation location for install sensor VEGA and pulling cable at truck lift ( JAJAT & RIZAL )

Pulling cable for welding point from junction box to location connected cable. Install scafolding at location to make safe while pulling cable welding heat exchanger ( EDI & MUHAIMIN & EVE FAJAR & DADANG )

Do drawing electrical for area truck lift save file at computer ( AGUS )

Make data spare part  Cabinet 61 and safe file at computer as Satelit Electric Kiln Form 14-8-25 ( JAJAT & ADI )

Clean up flange probe, sample line, filter sample line, diaphragm pump, filter balston dryer gas pump from dirty of coal. Check humidity sensor and filter humidity, result function ok and filter good condition ( RIZAL & ANDRI )

Do prepare cable and support for welding point at heat exchanger ( MUHAIMIN & EVE FAJAR &  DADANG )

Do drawing electrical for area truck lift save file at computer ( AGUS )

Make data spare part Cabinet 49 - Cabinet 50 - Cabinet 56 - Cabinet 63 and safe file at computer as Satelit Electric Kiln Form 13-8-25 ( JAJAT & ADI )

Do prepare cable welding heat axchanger ( EDI & MIHAIMIN & DADANG )

Do drawing electrical for area truck lift save file at computer ( AGUS )

Do cleaning motor CV at cyclone cooler from dirty of dust ( EDI & MUHAIMIN & DADANG )

Clean motor purge air unit and filter purge air unit, flange with tube dust hunter-swivel wndows transciever / reciever also reflector-alignment dust hunter, transducerA and transducer B of flowsic 100, CEMS room also gas room, filter cabinet MCS 100 E from dirty of dust ( RIZAL & ANDRI )

Make data spare part Cabinet 83 - Cabinet 82 - Cabinet 51 - Cabinet 57 and safe file at computer as Satelit Electric Kiln Form 12-8-25 ( JAJAT & ADI )

Make drawing electrical for truck lift save at computer ( AGUS )

Check autodrain function normal, found MC is failure ( RIZAL & ANDRI )

Clean up area motor and filter motor. Measure vibration - noise - temperature FS and LS. Add grease motor for FS and LS 20 times - 25 times - 30 times ( EDI & MUHAIMIN & DADANG )

Make data spare part Cabinet 84 - Cabinet 76 - Cabinet 77 and safe file at computer as Satelit Electric Kiln Form 11-8-25 ( JAJAT & ADI )

Do prepare cable for support automation L3C TL1. Bring cable to location continue pulling cable ( JAJAT & RIZAL & AIMAN & ANDRI & MUHAIMIN & DADANG )

Do install welding point at heat exchanger 2nd floor ( ANDRI & DADANG )

Make data spare part cabinet 71 - cabinet 72. Safe file at Satelit Kiln Form 8-8-25 ( JAJAT & ADI )

Clean up area MCC ER3 & ER4 top also bottom and filter cabinet. Continue mop ER3 & ER4  ( AIMAN )

Do data spare part at work shop for Cabinet 64 - Cabinet 65 - Cabinet 66 - Cabinet 70. Safe file at Satelit Kiln Form 7-8-25 ( JAJAT & ADI )

Do preparing welding point at heat exchanger ( AGUS & DADANG )

Do install connection support welding point at BAC. Continue connect cable power at panel welding panel and ER6 ( RIZAL & EDI & MUHAIMIN & ANDRI )

Clean up area MCC ER6 and ER5 top also bottom and filter cabinet from dirty of dust. Continue mop electrical room ( AIMAN )

Inspection electrical of PT AAS, 2 extention cable, 1 hot box, 1 main instrumentation tagging blue color ( JAJAT & ADI )

Make canopy motor for bag filter and bucket elevator raw mill, paint yellow color and install at location ( MUHAIMIN & ANDRI )

Check found bearing motor dry. Number bearing 6312 ZZ C3 & 6212 ZZ C3. Replace bearing motor waiting alignment from CMB team ( EDY & DADANG, MUHAIMIN ,ANDRI )

Prepare cable tray at work shop. Install welding panel  at BAC and cable tray beside welding panel. Put cable power for welding at cable tray ( ADI & ANDRI & MUHAIMIN )

Clean up panel control and I/O for reclaimer use hand blower from dirty of dust coal ( JAJAT & EDI & ADI )

Do prepare welding point panel of heat exchanger at work shop. Do wiring panel welding ( AGUS )

Replace lighting lamp off 3 each with spare lighting lamp, test function result lighting lamp on ( EDI & DADANG )

Clean flange probe, filter sample line, sample line, diaphragm pump, dryer gas pump, filter balston from dirty of dust. Check humidity sensor and filter humidity, result filter good condition ( RIZAL )

Do fabrication support rail mount of BAC ( ANDRI & DADANG )

Do prepare box welding point for heat exchanger. Take box at ware house electric behind ER5. In order to new installation 2nd floor heat exchanger ( AGUS & DADANG )

Clean up motor purge air unit and filter purge air unit, flange with tube dust hunter-swivel window reflector & transciever / reciever -alignment dust hunter-transducer A & B for flowsic 100-CEMS room-CEMS gas room-filter cabinet MCS 100E from dirty of dust ( RIZAL )

Clean flange, sample line, filter sample line, filter balston, dryer gas, diaphragm pump from dirty of coal. Check humidity sensor and filter sensor result function normal and filter good condition ( ADI & MUHAIMIN )

Do fabrication support rail mount of BAC at work shop ( DADANG & ANDRI & MUHAIMIN )

Do collective wiring of PLC truck lift and rewiring safe file at computer ( AGUS )

Clean area motor  and filter motor. Measure vibration -  noise - temperature FS and LS motor. Add grease motor 25 times - 30 times for FS and LS motor. Replace battery for AUTO Grease at 363 MD1 2 each ( EDI & MUHAIMIN )

Clean up connector, on and off power before on power tighten cable control heat at card heat control, MCS 100 E running well ( RIZAL & ANDRI )

Do scanning check sheet PMR and WBI month of July 2025 send to Mr. Jajat. Make data spare part cabinet 60 - cabinet 59 safe at computer as Satelit Part Kiln Form 4-8-25 ( JAJAT & ADI )

Pulling cable power welding panel BAC at ER6 ( JAJAT, AGUS, EDI, RIZAL, ADI, MUHAIMIN, ANDRI, DADANG )

Check program and service radio link found there is no power replace power supply, test function result ok ( RIZAL & JAJAT )

Lifting motor spare from burner floor to location, install motor. Check ampere no load at ER5 result ok  around 26 to 27 ampere ( JAJAT, AGUS, EDI, RIZAL, ADI, ANDRI< MUHAIMIN, DADANG )

Lifting motor spare from burner floor to location, install motor. Check ampere no load result ok  around 26 ampere until 27 ampere. Install tapper lock, pulley motor, connect cable power motor ( AGUS, EDI, RIZAL, ADI, JAJAT, MUHAIMIN, ANDRI, DADANG )

Check program and service radio link found there is no power replace power supply, test function result ok ( RIZAL & JAJAT )

Check program ok, found there plate torn at steering side material,  Observation Travelling ( RIZAL & EDI & ANDRI )

Replace stop  contact test function lighting lamp result ok ( EDI & DADANG & ANDRI )

Prepare Elect shop Hoist-rewiring ( AGUS & MUHAIMIN & DADANG )

Fabrication propeller sensor, and do adjust position. Test function result ok ( EDI & RIZAL & ANDRI )

Make data spare part cabinet 53 - cabinet 54 - cabinet 58 safe at  Safe file at computer as Satelit Part Electric Kiln Form 1-8-25 ( JAJAT & ADI )

Do scanning check sheet for PMR and WBI month of June 2025 send to Mr.Jajat email. Print out check sheet PMR and WBI 3 copy every check sheet. Make data spare part cabinet 52 Safe file at computer as Satelit Part Electric Kiln Form 31-7-25 ( JAJAT & ADI )

Clean up flange, sample line, filter sample line, diaphragm pump, filter balston, dryer gas pump from dirty of dust coal. Check humidity sensor and fiter sensor result filter condition ok ( RIZAL & ANDRI )

Install motor circulation at HRG test function result ok ( JAJAT & MUHAIMIN )

Check Auto grease motor, add empty level Auto grease motor for 473 FA2- 473 FA3 - 473 FA6 and check battery replace with spare battery for 473 FA1 - 473 FA3 - 473 FA8 - 473 FA9 - 473 FAA test function result ok ( EDI & MUHAIMIN )

Install Auto Greasing motor ( AGUS & DADANG )

Check condition actual motor measure use Megger ( AGUS & RIZAL & MUHAIMIN & DADANG & ANDRI )

Clean up motor and install AUTO Grease motor ( DADANG )

Clean up I/O panel area Raw Mill ( ANDRI )

Complete data check sheet PMR analyser L63 2K1-L63 2K2-L63 2K3-483 2K1-463 2K1-443 2K1-423 2K1 and WBI Feed Bin-Raw Mill-CT-Dust Transport-BF-Bottom Blending-Kiln-Cooler-Clinker Silo-Top Blending-CT-PH-Kiln-Coal Mill-Truck Lift-BC Transport-Tripper Reclaimer Coal month of June 2025 ( JAJAT & ADI )

Replace AUTO grease with spare full ( JAJAT & AGUS )

Make list observation for posibility recondition motor at OH 2026 ( AGUS )

Replace lighting lamp at 333 WF1 and lighting off, result test on lighting lamp on ( EDI & RIZAL & ANDRI )

Make data spare cabinet 13 - cabinet 19 - cabinet 20 - cabinet 21. Safe file at computer as Satelit Part Electric Kiln Form 29-7-25 ( JAJAT & ADI )

Complete data TPM ER4, save data at computer, print out install at dash board take print out TPM ER4 at CCR bring to work shop. Make data safety at SHE SIG print  out install at dash board. Take board for TPM at civil building work shop bring to electrical work shop ( RIZAL & ADI & EDI )

Prepare support sensor temperature at work shop, install sensor temperature at camera burner. Result ok ( RIZAL & ANDRI )

Clean up area motor and filter motor. Measure vibration-noise-temperature for FS and LS add grease 25 times-30 times for FS and LS to make vibration below 4 mm/s and noise below 2 gE ( AGUS & EDI )

Clean up area ER4 front and inside, do documentation for TPM. Make documentation safety area at ER4 send to Mr. Rizal for data TPM ER4 ( RIZAL & ADI & AIMAN )

Install temperature of DE and NDE  check indication temperature at CCR result are indication temperature high do check range temperature at CCR add cooling air at motor result temperature stable at 73 degree celcius. Clean up area motor 363 MD1, 363 FN1 & 363 FN2 also clean carbon brush 363 MD1 after clean up carbon brush room area use instrument air supply. Check bearing motor for greasing, do add greasing at main drive raw mill, 363 FN1 & 363 FN2 ( JAJAT & AGUS & EDI & ANDRI )

Complete data TPM ER4 save at computer ( RIZAL )

Complete data check sheet PMR service analyzer L63 2K1-L63 2K2-L63 2K3-483 2K1-463 2K1-443 2K1-423 2K1 for 3rd weeks of June 2025, PMR service critical motor RM-PH-CM-CC1 for month of june 2025 ( JAJAT & ADI )

Preparing control and pulling BAC room ( AIMAN & ANDRI )

Clean up flange, sample line, filter sample line, diaphragm pump, filter balston, dryer gas from dirty of coal. Check humidity sensor and sensor humidity result filter ok ( RIZAL )

Pulling cable 6 pairs from motor to  ST 12 ( AGUS & EDI & ANDRI )

Make data spare part cabinet 33 - cabinet 25- cabinet 26- cabinet 27- cabinet 32  write at PC as Satelit Part Electric Kiln Form 24-7-25 ( JAJAT & ADI )

Make data spare part cabinet 46 - cabinet 43 - cabinet 44- cabinet 45 - cabinet 23 - cabinet 38 - cabinet 39 - cabinet 37 write at PC as Satelit Part Electric Kiln Form 23-7-25 ( JAJAT & ADI )

Cross check indication temperature compare with display result ok different 6 until 7 degree celcius ( AGUS )

Clean up flange, probe, filter sample, sample line, diaphragm pump, filter balston, dryer gas pump from dirty of dust. Check humidity sensor and fiter sensor result filter sensor ok ( RIZAL )

Clean up area LS - area control - and radio link from dirty of dust coal use instrument air. Add silicone for cable gland ( EDI )

Make data spare part cabinet 46 - cabinet 47 - cabinet 48 write at PC as Satelit Part Electric Kiln Form 22-7-25  ( JAJAT & ADI )

Decrease setting speed from 47 Hz to 35 Hz, decrease decelaration setting ( parameter C1-2 & C1-4 ) from 10 s to 5 s, setting stick limit switch travel result function tripper ok ( AGUS & EDI & ANDRI )

Cross check at CCR operator indication vibration value 0 mm/s ( AGUS & EDI & ANDRI )

Blowing piping sample result flow back to normal indication ( RIZAL & ANDRI )

Adjust speed sensor result ok ( JAJAT & EDI )

cross check speed sensor result ok ( AGUS & EDI )

Replace solenoid valve, test function result ok s/v normal ( RIZAL &  ANDRI )

Clean up area motor and filter motor. Measure vibration - noise - temperature for LS and  FS. Add grease 20 times  - 25 times and 30 times for FS and LS motor ( AGUS & EDI )

Make data spare part cabinet 34 - cabinet 35 - cabinet 36 write at PC as Satelit Part Electric Kiln Form 21-7-25 and add spare part for cabinet 10 for vibration sensot  ( vibration transmitter 4 each brand ifm electronics ) ( JAJAT & ADI )

Activation DALOG accompany expert engineer DALOG ( RIZAL & EXPERT DALOG ENGINEER )

Prepare cable consumable for truck lift ( EDI & AGUS & MUHAIMIN & DADANG & AIMAN )

Do project 483 FA2, prepare cabinet, cable needed at cabinet ( AGUS )

Do install memory card CCTV cooler ( ANDRI & DADANG )

Make file data spare part at PC as Satelit Part Electric Kiln form 18-7-25 for cabinet 22 - cabinet 23 - cabinet 24 - cabinet 28 - cabinet 29 - cabinet 30. Complete check sheet PMR service analyser for L63 2K1-L63 2K2-L63 2K3-483 2K1-463 2K1-443 2K1-423 2K1 for month of 2nd week of July 2025( ADI )

Do WBI Elec & Ins & Check I/O GCT, EP,PH&KL and re check  Amp L63-SR1 isuuse Fluctuation ( RIZAL & ANDRI )

Install motor cooling motor ( MUHAIMIN & DADANG )

Make data file spare part work shop cabinet 6 - 10 - 11 - 12- 16- 17safe at Satelit Part Electric Kiln form 17-7-25 ( EDI & ADI & JAJAT )

Make data file spare part work shop cabinet 5 safe at Satelit Part Electric Kiln form 16-7-25  ( JAJAT & ADI )

Inspection electrical and welding tools of PT Truba Jaga Cita at 8th and 4th floor of pre heater and work shop mechanic 1 tagging blue color for electrical totals 45 unit consits: extention cable - portable lamp - impact wrenh - grinding machine - drilling machine, for welding totlas 8 units ( JAJAT & ADI )

Clean up flange sample, filter sample, sample line, diaphragm pump - filter balston - dryer gas from dirty of dust coal. Check humidity sensor and filter humidity sensor result filter ok ( RIZAL & ANDRI )

Replace motor cooling blower 473 FA5 & 473 FA6. Bring down ex  motor cooling blower to work shop ( MUHAIMIN & ANDRI & DADANG )

Make data spare part at work shop and write file at PC as Satelit Part Electric Kiln form 15-7-25  cabinet 1 - cabinet 2 - cabinet 3 ( JAJAT & ADI )

Project 483 FA2 ( AGUS & EDI & DADANG )

Clean up area purge air unit and filter purge air unit, swivel window T/R & R of dust hunter also flange with tube do alignment dust hunter, transducer A & B of flowsic 100, CEMS rooms, filter cabinet MCS 100 E and CEMS gas room from dirty of dust ( RIZAL & ANDRI )

PMR service elevator, clean up elevator room and top side also control at 8th floor from dirty of dust test run elevator from 8th to 1st floor result ok. WBI sump pump for elevator  result ok ( MUHAIMIN )

Complete data check sheet PMR MCC load UPS and PLC ER5. Make data spare part every panel safe at PC as Satelit Part Electric Kiln form 14-7-25  start cabinet 1 ( ADI )

Continue project motor 483 FA2 ( AGUS & DADANG )

Clean up probe, flange, filter sample, sample line, diaphragm pump, filter balston from dirty of dust. Check humidity sensor and filter humidity result filter ok ( RIZAL & ANDRI )

Clean up area motor, filter motor. Measure vibration - noise - temperature FS & LS motor. Add grease 20 times - 25 times - 30 times for FS & LS motor ( MUHAIMIN )

Complete data check sheet PMR MCC load UPS and PLC ER5 ( JAJAT & ADI )

Clean up probe, cooling fan, rail probe from dirty of dust. Check humidity sensor result filter ok Result CO: 0.004 vol% - NO: 960 PPM - O2:  5.44 vol% ( ADI & EVE HADIF & EVE ANDRE )

Check at location found sensor temperature already install ( RIZAL & EVE IDAM )

Complete data check sheet PMR analyzer L63 2K1-L63 2K2-L63 2K3-483 2K1-463 2K1-443 2K1-423 2K1; PMR IR TAD-T Scanner-CCTV-Camera Burner ( Pyrometer ) ( ADI & EVE  ANDRE )

PMR service IR TAD-T scanner-CCTV- Camera burner Pyrometer clean lens and flange  from dirty of dust ( ADI & EVE ANDRE )

Test on motor check rotation - load ( JAJAT & EDI & MUHAIMIN & ANDRI )

Find new motor at ware house bring to site and lifting to location. Dismantle existing motor 473 FN4 bring to work shop. Install new motor at site and install cable motor to LCS ( JAJAT & EDI & AGUS & RIZAL & ADI & MUHAIMIN & DADANG  & EVE IDAM & EVE ANDRE & EVE HAFID )

Take garbage at floor put back in garbage tank from Feed Bin to Raw Mill ( EDI & ADI )

Repare focus camera CCTV at south side 3 ( AGUS & JAJAT )

PMR MCC load also UPS ER5 and PLC CCR ( EDI & ADI )

Clean up purge air unit and filter purge air unit, swivel window T/R & R for dust hunter also flange with tube and alignment dust hunter from dirty of dust, transducer A & transducer B flowsic 100 from dirty of dust, CEMS room gas bottle also CEMS room and filter cabinet MCS 100 E from dirty of dust ( RIZAL & ANDRI )

Fabrication frame UPS ER3 and 483 FA2 ( ANDRI & DADANG )

Take garbage at floor put back in garbage tank from Feed Bin to Raw Mill ( EDI & ADI )

Install dozing motor of HRG. Test function result ok ( EDI & JAJAT )

Clean up probe-flange-filter sample line-sample line-filter balston-diaphragm pump from dirty of dust. Check humidity sensor and filter sensor result filter still function and normal. Found leakage at probe 463 2K1 observation suspected leakage, replace probe with spare probe, test leakage at work shop result ok, install at site. Test function insert and retract result ok ( RIZAL & EDI & MUHAIMIN & ANDRI & DADANG & ADI )

Do fabrication frame of UPS ER3 and 483 FA2 ( EDI & ANDRI & DADANG )

Take computer at hydraulic room bring to work shop. Setting computer for CCTV great cooler. Install CCTV great cooler ( AGUS & JAJAT )

Clean area motor and filter motor. Measure vibration-noise-temperature FS and LS motor.  Add AUTO grease at L63 MD1 found empty tank AUTO Grease motor. Add grease from 20 times and 30 times at FS also LS in order make vibration below 4 mm/s and noise below 2 gE ( ADI & MUHAIMIN )

Install CCTV at great cooler and supporting camera. Setting address for CCTV great cooler result ok ( AGUS & RIZAL & ANDRI )

Replace carbon brush, do cleaning motor 363 MD1 and filter 363 FA2 also replace belt motor e each do alignment test run motor check ampere result 152 A-149 A-154 A and check vibration vibration horizontal for FS and LS  high 3.8 mm/s ( EDI & MUHAIMIN & DADANG & ADI )

Replace battery UPS ER3 totals18 units. Bring ex battery to waste room of environment ( JAJAT & AGUS & RIZAL & ADI & ANDRI )

Pulling cable LAN CCTV great cooler from site to hydrolic room ( AGUS & MUHAIMIN & ANDRI & DADANG )

Complete data form WBI & PMR month of June 2025 do scanning for all data send to Mr.Jajat email ( EDI & ADI )

Clean up flange sample line,  filter sample line, sample line, filter balston, diaphragm pump, dryer gas pump from dirty of coal. Check humidity sensor and filter humidity result ok ( EDI & ADI )

Repare flaper analyzer. Test retract and insert result ok function flapper normal ( RIZAL & ANDRI )

Calibration zero and span for measurement gas result ok ( JAJAT & EVE IDAM )

Do preparing wiring instalation upgrade  for 483 FA2 and 473 FA2 ( AGUS )

Fabrication support line grease at work shop result ok ( RIZAL & ANDRI )

Complete document PMR and WBI. Rewrite for name file of PMR also WBI issue different number from name file install compare actual number file at cupboard reprint and install at cupboard of file ( JAJAT & ADI )

Observation motion detector, found there is no jumper cable at terminal sensor, do simulation disconnect cable result belt conveyor stop sensor function normal. Check distance probe sensor to media result ok ( MUHAIMIN & DADANG )

Cleaning  Area  Cyclone Cooller & Damper 473-FN7 and tidy  up spare part at work sop ( JAJAT & IMAN )

Complete WBI electrical & instrumentation area feed bin-raw mill-CT-dust transport-bag filter; CM-truck lift-BC transport-tripper-reclaimer coal; top blending-CT-PH-KILN; bottom blending-KILN-CC1-clinker silo ( JAJAT & ADI )

Check at local for compartemen 8 and compartemen 7. Jumpered DO result normal. Suspected sequence program problem make compartemen 7 & 8 are not working normal ( RIZAL & ANDRI )

Check AUTO grease at 483 BL7 & 483 BL9, found connector for grease plug. Replace  2 connector for motor, install 3 way connector from AUTO grease to motor. Result working normal ( MUHAIMIN & EVE RAIHAN )

Replace lamp area belt feed 3 units, test on result ok lighting lamp on ( FIRMAN & DADANG )

Complete data check sheet PMR analyzer 423 2K1-463 2K1-443 2K1-L63 2K1-L63 2K2-L63 2K3-483 2K1; PMR camera burner-IR TAD-CCTV-T scanner; PMR hoist crane; PMR service critical motor KILN-RM-CM-CC ( JAJAT & ADI )

Inspection electrical tools of PT INDOPORLEN totals 5 units: 3 jack hamer, 1 gunning machine, 1 water pump all tagging green color ( ADI )

Assembling motor 454 BL1 issue motor grounded, after service and add insulating spray at rotor motor result ok ( HARIYANTO & MARDIYANTO & ADI & DADANG & CIVACON ) 

Inspection electrical tools of PT Indoporlen totals 2 unit2; PT Mega Volts Perkasa total 1 unit all tagging green color ( TITOK & ADI )

 | Service dan test RTD L64-SR1.Ti1 (Temperatur Under Bearing Separator) 

 | Disconnect dan lepas sensor RTD L64-RM1.Ti8 

 | Disconnect dan Relokasi untuk mengamankan Probe Filter Analyzer L64-2K1 dan Saluran Cocair 

 | Disconnect Proximity Sensor 2 Ea

 | Manuver Power 

Lepas Transmitter 

 | Lepas Transmitter 

Lepas Transmitter 

 | Wrapping All Panel Aerasi 

 | Disconnect, lepas sensor Temperature 

Disconnect, lepas sensor Temperature 

 | Disconnect, lepas sensor Temperature 

Bongkar Motor PF , Wrapping Panel 

 | Bongkar Motor PF , Wrapping Panel 

Bongkar Motor PF , Wrapping Panel 

Check speed sensor,beltdrift dan kalibrasi

Repair dudukan speed sensor,check switch belt drift

Replace temp transmitter 

Connect new transmitter 

Completing data for calibration temperature and pressure transmitter OH NR2 ( TITOK & ADI )

Check safety device

Check safety device

Instal temperature transmitter,connect to i/o

Repair actuator macet,test open close dan check indikasi dr I/O

Do calibration temperature transmiter area RM total 2 unit 364 SR1 T2-364 RM T1; 364 FN3 T1-364 FN3 T2; 364 FN4 T1-364 FN4 T2; 424 FN1 T1-424 FN1 T2 replace with Endess Hauser-424 FN1 T3 for zero 0  degree celcius and span 150 degree celcius result ok ( MUHIB & ADI & CIVA SUPRIYADI )

Service dan repair solenoid valve

Check dan service sensor level dan sensor ML

Replace timer purging

Replace bray valve

Replace bray valve

Run local motor EP fan, try run 50% and 80% RPM, measure vibration below 0 mm/s, noise below 1 gE ( HARIYANTO, ADI )

Do scanning data check sheet calibration pressure-temperature transmitter-inspection electrical & welding tools OH NR2 ( ADI & EVE RAIHAN )

Inspection electrical and welding tools of PT Quadro Indonesia 1 unit purification machine, PT Deco Mandiri Sejahtera 1 unit welding machine-2 drilling machine, PT Aqpa Indonesia 3 unit extention cable- 2 unit drilling machine all tagging green color ( ADI & TRUBA SUTRI &  EVE RAYHAN )

Inspection electrical and welding tools of PT Deco Mandiri Sejahtera rejected 2 extention cable because not full fill requirement safety no cover and PT Truba Jaga Cita, all tagging green color ( TRUBA SUTRI & TRUBA SUSILO )

Replace pressure transmitter for 446 PH1 PT3 and calibration zero also span result ok ( ADI & EVE RAYHAN )

Inspection electrical & welding tools of PT Cahaya Abadi Teknik, PT Bouveri all tagging green color ( TRUBA SUTRI & TRUBA SUSILO )

Calibration pressure transmitter area pre heater-rawmill totals 10 units ( ADI & YOGA )

Instal TE exit mill,bottom CT dan buat lubang baru TE exit mill(fail)

Instal pressure tx area Rawmill

Test counterweight dan coil auto balancer

Replace sensor ML

cleanup and test function ACB

Inspection electrical & welding tools of PTCIVACON total 2 unit electrical tools: extention cable-grinding machine; PT Cahaya Abadi Teknik total 9 units welding tools: 3 unit welding machine-3 cable welding + & 3 unit cable welding - also 7 units electrical tools: 1 portable lamp-3 extention cable-3 grinding machine-1 line boring machine; PT RMP total 1 unit eletrical tools: 1 gunning machine all tagging green color ( ADI & TRUBA SUTRI & TRUBA SUSILO )

Service,check dan replace solenoid dan selang purging

Service dan repair selang valve actuator
Replace flexible conduit
Check dan test sensor ML
Check dan test level sensor

Service dan repair valve bottom Ct
Replace regulator

Service dan repair safety device ep transport

Inspection electrical and welding tools of PT AQPA totals 21 units for electrical 20 units and welding 1 units, PT RMP for elecrical 4 units and welding 5 units cable welding ( ADI & TRUBA SUTRI & TRUBA SUSILO )

PMR analizer IKGA, clean up flange-filter sample line-sample line-diaphragm pump-filter balston from dirty of dust. Check humidity sensor and filter humidity result filter ok ( RIZAL & ANDRI )

Inspection electrical tools of PT Truba Jaga Cita for 2 blower tagging green color ( ADI & TRUBA SUSISLO)

pabrikasi support kabel, cover panel, torque terminasi kabel power, test open close vcb, cleanup ruangan vcb2

Check service dan test open close

Service,repair dan test damper

Service repair dan adjust 
Damper actuator
Continue check by mechanic

Activated speed sensor result ok ( RIZAL & ANDRI )

Install AUTO grease pump ( JAJAT & DADANG )

Inspection electrical and welding tools of PT Sentra AnekaTama found 1 extention cable is not safe no cover and welding machine failure also ground cable failure, PT Truba Jaga Cita, PT RMP all tagging green color ( ADI & TRUBA SUTRI & TRUBA SUSILO )

Check service dan test safety device

Check service dan test safety device

Check service dan test safety device

Chwck service dan test safety device

Check service dan test safety device

Cleaning All ( PLC, Drive, MC, Cabin) ( JAJAT & DADAMG )

Inspection electrical and welding tools of PT Mujur Manggana Megah, Plant building connected cable power portable lamp 10 units also tagging green color, Truba Jaga Cita, all tagging with green color ( ADI & TRUBA SUTRI & TRUBA SUSILO )

Koneksi dan Terminasi MV kabel dengan 3M

Precheck safety device

364 RM1 T1 T2
Replace thermocouple inlet Rawmill 2 eah

Check purging
Repair 1 purging ngowos bersihkan membran

disconect cable power, bongkar panel LBS & pindahankan ke gudang er4 bawah, pabrikasi support panel VCB2 

Do inspection electrical and welding tools of mechanical AFR also make 1 unsafe electrical tools because not full fill requirement safety and INDOPORLEN, tagging green color ( ADI & TRUBA SUTRI & TRUBA TRI SUSILO )

Install Blower  to Motor  Back actuator ( MUHAIMIN & ANDRI )

Inspection electrical and welding tools of plant buildinng also repare extantion cable and grinding machine because cable grounding of make danger note for grinhding machine and extantion cable because are bot safety and failure. Inspection electrical and welding of suplier at main gate, Inspection jack hamer of CIVACON. all tagging green color ( ADI & TRUBA SUTRI & TRUBA TRI )

Replace  Rel, Cleaning Probe, Calibration Sensor  ( RIZAL & ANDRI )

Clean up motor and filter motor. Measure vibration-noise-temperature FS & LS motor. Add grease 25 times & 30 times for FS & LS motor until vibration below 4 mm/s and noise below 2 gE ( MUHAIMIN & EVE RAYHAN )

 Check solenoid purging kondisi kerja semua
Clean up box panel

Check motion detector kondisi visual masih OK

Disconnect dan discouple All pressure transmitter area Raw Mill

Repair box yg lepas
Repair cable gland
Simulasi sensor result good

Repaire cable gland,repair box mau lepas,simulasi sensor ML result good

Inspection extention cable 9 unit tagging with green color, repare 3 unit extention cable because cable grounded loose also replace male and female connector ( ADI )

Inspection electrical and welding tool, tagging green color ( FIRMAN & DADANG )

Install lighting lamp for 2 tent and toilet beside work shop nr1, tent OH near work shop mechanic and L63 RM1 ( IMAN & MUHAIMIN & ANDRI & FIRMAN & DADANG )

Complete data check sheet PMR analyzer L63 2K1-L63 2K2-L63 2K3-483 2K1-463 2K1-443 2K1-423 2K1; PMR IR TAD-CCTV-T Scanner-Camera Burner for June 1st weeks. For 423 2K1 complete month April & May 2025 ( ADI & EVE IDAM ) & JAJAT )

Prepare drawing diagram and IO needed also instalation drive 483 FA2 ( AGUS & FIRMAN & MUHAIMIN & EVE IQBAL )

Clean up flange, sample line, filter sample line, filter balston, diaphragm pump, dryer gas from dirty of coal. Check humidity sensor and filter sensor, result filter ok ( ADI & EVE IDAM )

Service sensor speed switch, test function result ok ( RIZAL & ANDRI )

Replace lighting lamp with spare lamp, do test on lighting lamp result ok lamp on ( FIRMAN & DADANG )

Clean up MCC ER3 & ER4 top and bottom floor, filter cabinet, electric room from dirty of dust use brush and vacuum cleaner. Also mop floor top and bottom. Also area motor 423 BF1 ( JAJAT & AIMAN )

Clean up flange, filter sample line, sample line, diaphragm pump, filter balston, dryer gas pump from dirty of dust. Check humidity sensor and inspection filter result filter ok ( AGUS & ANDRI & EVE IQBAL )

Replace lighting lamp with spare lamp test on result lighting lamp on ( FIRMAN & DADANG )

Clean up motor and filter motor. Measure vibration-noise-temperature FS & LS motor. Add grease 25 times and 30 times for FS & LS make vibration below 4 mm/s, noise below 2 gE ( MUHAIMIN & EVE IDAM )

Complete stop log PMR, scan data for AUDIT API send to Mr. Jajat ( JAJAT & ADI )

Inspection electrical and welding tools total 29 units tagging blue color ( electrical tools: 25 units, welding tools: 4 units ) ( ADI & EVE IDAM )

Clean up motor purge air unit and filter purge air-unit swivel window T/R & R of dust hunter, flange with tube dust hunter-alignment dust hunter result ok-transducer A & B flowsic 100-CEMS room-filter cabinet of MCS 100 E-gas room of CEMS from dirty of dust ( RIZAL & ANDRI )

Clean up motor and filter motor, measure vibration-noise-temperature FS & LS motor. Add grease 20 times and 25 times for FS & LS motor make vibration below 4 mm/s, noise below 2 gE ( MUHAIMIN & EVE IDAM )

Clean up motor and filter motor, measure vibration-noise-temperature FS & LS motor. Add grease 20 times and 30 times for FS & LS motor make vibration below 4 mm/s, noise below 2 gE ( AGUS & DADANG )

Check sheet result found 3 file: PMS 463 KL1 frequency 120 days, PMR MV motor frequency 120 days, Speed Calibration frequency 1 years ( ADI & EVE IDAM )

Do top up grease of L63 SX1 M1. Measure vibration-noise FS & LS result normal

Do top up grease of L63 LQ1 M1. Measure vibration-noise FS & LS result normal ( MUHAIMIN & FIRMAN & DADANG )

Check at local, found propeller sensor broken, service propeller at work shop. Install sensor ML at local test function result ok ( RIZAL & ANDRI & EVE IQBAL )

Clean up flange, sample line, filter sample, diaphragm pump, filter balston, dryer gas pump  from dirty of coal. Check humidity sensor and filter humidity sensor, result filter ok ( ADI & EVE IDAM )

Check temperature and ampere for trafo cable at ER4 result ok. Put spare battery UPS  20 each at ER4 ( FIRMAN & MUHAIMIN & DADANG )

Do fabrication cover battery ( FIRMAN & DADANG )

Complete data PMR & WBI for month 2025 from January until May 2025 continue scan all data send to Mr.Jajat email. Complete data check clean up MCC ER3-ER4-ER5-ER6 from december 2024 until may 2025 ( ADI &  JAJAT & FARCHAN & EVE IDAM )

Do WBI Elect & Ins & Check I/O CM,Sump T&T. Measure vibration-noise-temperature FS & LS motor. Write not normal vibration and noise motor ( RIZAL & ANDRI & EVE IQBAL )

Clean up flange, probe, filter probe, sample line, diaphragm pump, filter baltson, dryer gas pump from dirty of dust. Check filter humidity sensor, result filter ok ( RIZAL & ANDRI & EVE IQBAL )

Prepare ALL connection LAN (PC-CCTV,APC) , Pulling   cable Radio, Prepare PC Unit, Cleaning Filter Server , dismantling  table + accessories  ex  NAR 2 ( AGUS & JAJAT & ADI & FIRMAN & MUHAIMIN & ANDRI & DADANG & EVE IDAM & EVE IQBAL ) 

Complete data for preparing AUDIT API ( JAJAT & ADI )

Still observation, test Signal  Ok, confirm IT ( AGUS & ADI & DADANG )

Clean up area motor and filter motor. Measure vibration-noise-temperature free side and load side motor. Add grease 10 times for FS & LS until vibration & noise normal ( MUHAIMIN & EVE IQBAL & EVE IDAM )

Clean up motor and filter purge air unit, swivel window T/R & R dust hunter, and flange with tube dust hunter, alignment dust hunter, transducer A &B flowsic 100, CEMS room and filter cabinet MCS 100 E also gas bottle room from dirty of dust ( FIRMAN & ANDRI )

Do install and reconnect cable power for Operator Nr2 at CCR ( JAJAT & AGUS & RIZAL & ANDRI & FIRMAN & MUHAIMIN & ADI & DADANG )

Make notification for WBI electric and instrumentation bottom blending-cooler-clinker silo ( ADI & EVE IDAM )

Complete data dash board TPM L63 FN1 & L63 IP1. Print out at put at dash board work shop. Make safety file TPM also print out and put at dash board TPM work shop ( ADI & EVE IQBAL )

Install indication flow meter, result ok ( RIZAL & ANDRI )

Clean up area motor and filter motor. Measure vibration-noise-temperature motor free and load side. Add grease 20 times-30 times for FS & LS. Replace 3 unit carbon brush at 363 MD1 because actual long are short information from Mr.Najib CBM (MUHAIMIN & EVE IDAM )

Make reparing power greasing 473 FN4, replace power supply input 110-220 VAC and output 24 VDC, test function AUTO Grease motor result ok ( MUHAIMIN & DADANG )

Found card error at control flow meter advise need to replace ( MUHAIMIN & DADANG )

Install Water trap and Regulator ( RIZAL & ANDRI )

Do WBI area bottom blending-cooler-clinker silo. Measure vibration-noise-temperature FS & LS motor, write unnormal condition ( JAJAT & ADI )

Repare connection at  sensor, result indication temperature normal ( RIZAL & ANDRI )

Make fix connection power supply coal mill at HS room ( MUHAIMIN )

Check at location found there is no power for AUTO grease motor. Replace power supply 220 VAC to 24 VDC, test function result ok ( MUHAIMIN )

Clean up sensor and tighten cable because found untighten cable sensor, result indication temperature back to normal ( RIZAL & ANDRI )

Check at site, found cable at sensor is not tight, tighten cable sensor result indication temperature normal ( RIZAL & ANDRI )

Do support testing AUTO Balancer ( AGUS & FIRMAN & JAJAT )

Replace battery UPS ER-04 2402 6 unit ( AGUS & FIRMAN & DADANG )

Cleaning area HRG inside and outside room, filter at outside HRG room, PLC HRG from dirty of dust use instrument air supply and hand blower. Install level modification at WTP of HRG test indication al PLC already appear ( RIZAL & ADI & MUHAIMIN & ANDRI & DADANG & JAJAT )

Do completing data sheet WBI month of may 2025 ( ADI )

Install control sump pump. test function result ok ( FIRMAN & DADANG )

Check hoist crane at raw mill, adjust brake test function ok clean up area motor, rail continue test function motor move south-north-up and down result ok ( AGUS & FIRMAN & DADANG )

Check sensor BD, test indication at CCR. Do calibration zero and span result ok ( RIZAL & MUHAIMIN & ANDRI )

Modification temperature T1 and T2. Replace temperature transmitter 2 each result indication temperature normal at CCR ( RIZAL & ANDRI & MUHAIMIN )

Re check lighting lamp at pre heater 8th floor connect cable short at panel, test function result ok ( FIRMAN & DADANG )

Clean up I/O panel area blending-cooler-water spray kiln from dirty of dust use rag and hand blower ( JAJAT & ADI & EVE ANDRE )

Support AUTO Balancer. Install sensor ( AGUS & FIRMAN & DADANG )

Pulling cable power AC server room to CCR ( AGUS & FIRMAN & MUHAIMIN )

Do connected cable power motor and test run result ok ( AGUS & FIRMAN & MUHAIMIN )

Repaire propeller motion at motor. Result ok ( AGUS & FIRMAN & MUHAIMIN )

Do activation re-track for analyzer IKGA.  Test re-track and insert probe result ok ( RIZAL & ADI & ANDRI & DADANG )

Pulling cable digital input for indication low temperature heater CO2 liquid from control to I/O panel L63 HS1 continue connected cable white and brown. Test signal from heater control to I/O panel result ok blinking ( RIZAL & ADI & ANDRI & DADANG )

Do support alignment motor from CBM. Install AUTO grease motor. Measure data vibration 2 mm/s, noise 1 gE after alignment from CBM ( AGUS & FIRMAN & MUHAIMIN )

Do support instalation AUTO Balancer, found existing AUTO Balancer is bad condition suspected because fire case when kiln just start up and motor 443 FN1 is not starting full, when existing AUTO Balancer bring to work shop and measure resistance 9.5 ohm ( AGUS & FIRMAN & MUHAIMIN )

Do make data for KILN-RM-CM shut down-idle-PM-off save at D: as Data Kiln-RM-CM shut down-idle-PM-off 2025 ( JAJAT, ADI )

Inspection electrical and welding tools, tagging with green color ( ADI, DADANG )

Measure distance cable for analog input and digital input from heater control to I/O pnel L63 HS1 needed cable 30 meter ( JAJAT, ADI )

Do cleaning motor area cooler from dirty of dust ( JAJAT, ADI, DADANG )

Continue painting area TPM L63 FN1 ( DADANG )

Do create permit job replace AUTO Balancer ( ADI, EVE IQBAL )

service stick of roof switch, remove jumper cable at I/O panel after normal condition ( RIZAL, ANDRI, EVE IQBAL )

Do observation data base-frame-high shaft also diameter shaft, dismantle motor bring to work shop replace bearing motor 6217-C3 ( AGUS, FIRMAN, MUHAIMIN )

Cross check indication level with production team compare with indication level at local result same ( RIZAL & ANDRI )

Do observation Auto Balancer. Check coil winding ( AGUS & FIRMAN & DADANG )

Print out also laminating and install at dash board work shop for AM and for data TMP at dash board local and at tank of CO2 Systems for sign safety ( ADI & EVE IQBAL)

Clean up area motor use instrument air supply, also equipment cleaning for stair, plat form, cable tray. tank of CO2 system. Re painting yellow color for wall of foundation motor, grey for stair and iron around base foundation motor  and fence of CO2 system ( JAJAT & AGUS & RIZAL & ADI & EVE IQBAL & FIRMAN & MUHAIMIN & ANDRI & AIMAN & DADANG )

Add grease motor 10 times-25 times & 30 times result not good still high vibration up 4 mm/s & noise up 2 gE ( MUHAIMIN & EVE IQBAL )

Completing data check sheet PMR analyser and PMR IR TAD-T scanner-CCTV-Camera Burner for 2nd weeks ( JAJAT & ADI )

Do clean up AUTO Balancer at work shop ( AGUS & FIRMAN & MUHAIMIN )

Clean up flange, sample line, dryer gas pump, filter sample line, diaphragm pump, filter balston, humidity sensor from dirty of coal. Check filter humidity sensor result still ok no need replace filter ( RIZAL & ANDRI )

Clean up MCC ER3 & ER4, filter cabinet, also electric room top and bottom from dirty of dust use brush and vacuum cleaner ( AIMAN )

Clean up lens of CCTV-IR TAD-T scanner-Camera burner from dirty of dust. Note value IR TAD show 946 degree celcius after clean up ( ADI & EVE IQBAL )

Replace lighting lamp, test on result lamp on ( FIRMAN & DADANG )

Cleaning Line ( east side Blocking), Done , result indication pressure 10,8 mbar ( AGUS & FIRMAN & MUHAIMIN & EVE IQBAL )

Clean up area motor and filter motor. Measure vibration-noise-temperature FS and LS. Add grease 15 times-20 times & 30 times for FS & LS. Write ampere and voltage motor at ER3 & ER4 for actual motor ( MUHAIMIN & EVE IQBAL )

Add grease around 10 times until 25 times until vibration below 4 mm/s motor issue high vibration ( MUHAIMIN & EVE IQBAL )

Installing rack mount server at CCR ( DADANG & FIRMAN )

Clean up AUTO Balancer at work shop (AGUS & FRIMAN )

Make form calibration speed and damper at work shop continue print out. Completing data check sheet form calibration speed and damper for year 2025 ( JAJAT & ADI )

Replace pressure transmitter and relocation pressure transmitter result indication pressure normal at CCR  ( RIZAL & ANDRI & EVE ANDRE )

Cross check indication temperature T1 & T2 compare with CCR reading result ok ( AGUS & FIRMAN & MUHAIMIN )

Make support server rack mounts at work shop ( ANDRI & DADANG )

Clean area motor and filter motor. Measure vibration-noise-temperature FS and LS. Add grease 10 times for FS and LS and write data ampere-voltage actual motor at ER5 & ER4. Replace AUTO grease motor at 473 FA3 ( MUHAIMIN & ADI & EVE IQBAL )

Replace sensor temperature with spare unit becuase suspected original sensor temperature not long enough, result different temperature only 8 degree celcius ( AGUS & FIRMAN )

Clean up MCC of ER3, filter cabinet also electric room top and bottom from dirty of dust use brush and vacuum cleaner ( AIMAN )

Clean up MCC ER 5  top also bottom floor & ER6, filter cabinet from dirty of dust use brush and vacuum cleaner ( AIMAN )

Install lamp server and power of lamp server, dismantling power and installation LAN cable  ( AGUS & FIRMAN & DADANG & MUHAIMIN & JAJAT & RIZAL & ADI & ANDRI & EVE IQBAL )

Connect cable for final task and activation emergency retract ( do simulation and test result ok ) ( EVE RIQBAL & RIZAL & ANDRI )

Completing check sheet PMR and WBI for 2025 until May 2nd weeks, also take sign for every form. Replace data 423 2K1 PMR service because wrong form refill check sheet and take sign. Print out original form for PMR analyzer and WBI hoist crane ( JAJAT & ADI )

Do cross check signal R1 from local to CCR result ok ( MUHAIMIN )

Secure panel. pulling cable display, instalation power cable & prepare LAN 8 bundle at work shop do test result ok - standing monitor ( AGUS & FIRMAN & DADANG &  MUHAIMIN & JAJAT & RIZAL & ADI & ANDRI )

Do inspection electrical of PT PINCURAN MAS total 24 units tagging with green color

Do connect cable for final task of final task EVE ( JAJAT & RIZAL )

Replace 3 membran with spare unit, clean up ohter membran. Test function result ok membran purging ( RIZAL & EVE IQBAL & ANDRI )

Clean up MCC ER 3 & ER4 top also bottom floor, filter cabinet from dirty of dust use brush and vacuum cleaner ( AIMAN )

Clean up sample line, filter sample line, balston filter, dryer gas pump, humidity sensor from dirty of coal.Check filter humidity sensor result ok ( ADI & MUHAIMIN )

Pulling cable for final task  and re-program DCS ( EVE IQBAL & JAJAT )

Do certification flow meter diesel at burner floor and pre heater ( RIZAL & ANDRI )

Completing data check sheet for PMR analyzer L63 2K1-L63 2K2-L63 2K3-483 2K1-463 2K1-443 2K1-423 2K1 for month april & may 2025, PMR camera burner-t scanner-IR TAD-CCTV for month of may 2025, WBI top blending-CT-PH-kiln, bottom blending-kiln-cooler-clinker silo, feed bin-RM-bag filter-dust transport, CM-BC transport-truck lift-reclaimer coal for may & april 2025 ( JAJAT & ADI )

Replace sling for switch sensor, do test sensor result ok ( MUHAIMIN & DADANG )

Clean up probe, flange, sample line, filter probe, diaphragm pump, filter balston, dryer gas pump, humidity sensor from dirty of dust. Check filter humidity sensor result ok ( MUHAIMIN & DADANG )

Temporary activated LAN way ( AGUS & FIRMAN )

Re-Check ,result  still finish need root ( AGUS & FIRMAN & EVE IQBAL )

Adjust corection factor result reading coal ok ( RIZAL & MUHAIMIN & EVE IQBAL )

Make good direction of solenoid valve for water. Test function from CCR result ok ( RIZAL & MUHAIMIN & EVE IQBAL )

Do Certification antidote to evil spirits ( AGUS )

Install box server at work shop also connect cable server ( FIRMAN & DADANG )

Clean up area motor and filter motor. Measure vibration-noise-temperature FS & LS. Add grease motor from 15 times-25 times-30 times FS & LS motor ( MUHAIMIN & EVE IQBAL )

Clean up filter purge unit motor & filter, swivel window T/R & R for dust hunter also flange with tube and alignment T/R & R, transducer A & B flowsic, CEMS room and bottle gas room from dirty of dust ( RIZAL & ANDRI )

Tidy up spare part at work shop. Completing data motor survey energi bahaya for area blending top & bottom-pre heater-coal mill-cooler-clinker silo-truck lift & reclaimer motor base on data WBI at that area ( JAJAT & ADI )

Tidy up spare part at work shop. Completing data motor survey energi bahaya for area feedbin-raw mill-bag filter. Data motor base on WBI at that area ( JAJAT & ADI )

Replace ELCB welding at burner floor ( FIRMAN & DADANG )

Clean up area motor and filter motor. Measure vibration-noise-temperature FS & LS. Add grease motor from 15 times-25 times-30 times FS & LS motor ( MUHAIMIN )

Do certification antidote to evil spirits ( AGUS )

Install bright lamp at stair of CT, test on ok ( FIRMAN & DADANG )

Inspection electric and welding tools of PT Truba Jaga Cita ( Firman )

Install cover  give for AS as room sirculation for air ( FIRMAN & DADANG ) 

Install bright lamp, test on result ok ( FIRMAN & MUHAIMIN & DADANG )

Replace drain for air tank at burner ( RIZAL & ANDRI )

Clean up ER 3 & ER 4 top also bottom and MCC panel also filter cabinet from dirty of dust use brush  and vacuum cleaner ( IMAN )

Completing file check sheet  WBI Elect & Ins & Check I/O CM,Sump T&T also make notification for abnormal finding for vibration & noise motor

Trouble shooting for reading O2 high result ok ( RIZAL & EVE IQBAL & ANDRI )

Replace solenoid valve no 18 result ok ( MUHAIMIN & EVE IQBAL )

Pulling cable from MCC ER4 to local, do connection. Result ok ( RIZAL & JAJAT & ANDRI )

Clean up area CEMS room and bottle gas room from dirty of dust use brush. Check value of CEMS analyser reading result ok specially for MCS 100 E reading temperature heater result ok . Completing data check sheet 423 2K1  ( ADI & EVE IQBAL )

Do completing data TPM 443 EL1, print out and put at dash board TPM ( EVE IQBAL )

Check cable AUTO balancer reference to normal test to Nr2 result ok ( AGUS & FIRMAN & DADANG )

Replace heater control, trafo CEMS. Pulling cable from MCC to trafo also from output trafo to CEMS room. Conect cable at CEMS room, trafo and MCC. Test on result ok ( RIZAL & ADI & MUHAIMIN & AGUS & JAJAT & EVE IQBAL & FIRMAN & ANDRI & DADANG )

Clean up area motor and filter motor. Measure vibration-noise-temperature FS and LS motor. Add grease 15 times-20 times and 30 times for FS and LS motor ( MUHAIMIN & EVE IQBAL )

Do check sensor turbo coupling, found oil leakage ( AGUS & MUHAIMIN )

Do test AUTO balancer result ok ( JAJAT & RIZAL & ANDRI )

Tidy up cable temperature sensor T2 & T3 ( RIZAL & ANDRI & ADI )

Fabrication transfer hot air motor from main drive ( FIRMAN & DADANG )

Replace cell robicon ( AGUS & FIRMAN & AIMAN )

Do WBI Elec & Ins & Check I/O & S Pump Bl,C, measure vibration-noise -temperature write abnormal condition at file ( ADI & EVE IQBAL )

Check found membran bad condtion replace membran 5 each. Test run result ok no leakage ( RIZAL & ANDRI )

Simulation sensor ML at local and check indication at CCR. Clean up sensor ML test simulation result ok ( RIZAL & EVE IQBAL & ANDRI )

Fabrication for transfer hot air from main drive to reduce high temperature winding. Install at local, observation reading temperature winding motor ( FIRMAN & DADANG )

PMR critical motor Kiln and RM. Clean up area motor and filter motor. Measure vibration-noise-temperature add grease from 15 times, 25 times and 30 times fore FS and LS ( AGUS & MUHAIMIN )

Replace key pard analyzer and sensor O2. Test calibration zero and span O2 result ok ( RIZAL & ANDRI & EVE IQBAL )

On AUTOBALANCER replace breaker because when try to On trip. Test on AUTOBALANCER result ok ( RIZAL & EVE IQBAL & ANDRI )

PMR Clean Up MCC ER 3 top and bottom and ER6, clean up filter panel and MCC; and room electrical room from dirty of dust with brush and vacuum cleaner result ok + Cleaning Lamp area CM -Burner use equipment cleaning tools result ok ( AIMAN )

WBI Elec & Ins & Check I/O GCT, EP,PH&KL. Clean area motor, measure vibration, noise and temperature free and load side. Write at file inspection for all data

Scan all check sheet analyser month march 25 and april 25 send by email to Mr.Jajat

Fabrication blower at work shop and install at local. Test run result ok ( FIRMAN & DADANG )

Service L63 BV3, test from CCR result ok ( RIZAL & EVE IQBAL & ANDRI )

Cross check value for Temp-Amp-KW compare from local and CCR result ok ( AGUS & MUHAIMIN )

Completing data check sheet for PMR analyzer L63 2K1-L63 2K2-L63 2K3-483 2K1-463 2K1-443 2K1-423 2K1; PMR critical motor RM-CM-KILN-COOLER; WBI Top Blending-CT-PH-KILN; WBI Feed Bin-RM-CT-Dust Transport-BF for month March until April 2025 ( ADI & EVE IQBAL )

Replace vibration sensor AUTOBALANCER with spare result ok ( RIZAL & MUHAIMIN & DADANG & ANDRI & JAJAT )

Make analyzer AUTO result ok ( RIZAL & ANDRI )

Adjust indication with zero adjust  result ok ( RIZAL & ANDRI )

Clean lens CCTV-IR TAD-Kiln Scanner from dirty of dust. Clean up panel of oil and water trap and panel control camera burner from dirty of oil and dust also panel instrument air out side from dirty of dust use hand blower and cloth ( ADI & EVE IQBAL )

Replace tubing copper tubing-connector tubing, also S/V test run result ok ( RIZAL & EVE IQBAL & JAJAT & ANDRI )

Support test AUTO BALANCER ( JAJAT & RIZAL & EVE IQBAL & ANDRI )

Install plat form HRG or WTO and commisioning HRG ( RIZAL & JAJAT & EVE IQBAL & ANDRI )

Support PT LOUSER instalation wire rope ( AGUS & FIRMAN )

Test signal S for 493 FN3 & FN4, replace contactor emergency stop test run signal S result ok ( ADI & MUHAIMIN & DADANG )

Test signal roof switch R1 at 493 AC2 & AC4, clean up area sensor add WD 40 for stick test run result ok Test signal S for 493 AC2, AC3 and AC4 result ok ( MUHAIMIN & ADI & DADANG )

Relocation new operator for cable VEGA-power supply monitor-LAN. Test on monitor result ok ( JAJAT & AGUS & MUHAIMIN & ADI & DADANG )

Do support gear box instalation and finishing instalation 363 MD1 ( AGUS & FIRMAN & DADANG )

Rewiring control hoist belt feed 333 EH1 ( FIRMAN & EVE IQBAL )

Check cable for vibration AUTOBALANCER, repare separated cable result ok. Check vibration sensor at AUTOBALANCER ( RIZAL & ADI & ANDRI )

Install plat form HRG or WTP ( RIZAL & ANDRI & ADI )

Repare connection result value back to normal ( AGUS & MUHAIMIN )

Replace cable welding that are burned with spare cable ( FIRMAN & DADANG )

Relocation proximity ( ANDRI & EVE IQBAL )

Clean up area inspection grate cooler from dirty of dust, replace 1 limit switch because bad condition also install 1 stick limit switch. Test on lamp result ok from compartemen 1 to 7 ( JAJAT & ADI & ANDRI & DADANG )

Pulling cable for bearing temperature motor from locat to panel I/O also do connection cable at local and panel I/O ( AGUS & JAJAT & MUHAIMIN & ADI & DADANG )

Rewiring control VCS ( AGUS & MUHAIMIN )

Connect cable motor ( FIRMAN & DADANG )

Repare hoist of raw mill ( FIRMAN & DADANG )

Do disconnect pipe for H2 & O2 ( RIZAL & ANDRI )

Re-fill grease test result ok ( RIZAL & ANDRI )

Make sure heater function result ok ( FIRMAN & DADANG )

Do modification control pump of clorine at HRG, also add silicone for outside BLUEBOX panel ( JAJAT & ADI ) 

Cleaning LCS panel area Tyre Kiln and 473 CC1 use putty knife, soft brush, rag, vector from dirty of dust ( JAJAT & ADI & IMAN )

Do rewiring control VCS ( AGUS & MUHAIMIN )

Replace  new one (6 EA) ( FIRMAN & DADANG )

Cleaning oil drum 453 PF1 also add oil omala 300 adjust gap. Test  LC found 1 bad condition. Replace LC test load from person weight 6 person. Re test 483 PF1 because CF original 5 change to 0 after load use ( RIZAL & ANDRI & ADI )

Service roof for SW result ok ( FIRMAN & DADANG )

Make swap cable power motor test run result ok. Install cover for bar ( FIRMAN & DADANG )

Send motor to ware house for repairing ( FIRMAN & DADANG )

Do test solenoid valve function result 1 no good condition. Replace S/V with spare test run result ok ( RIZAL & ANDRI & ADI )

Cleaning area Pfister Feeder from dust coal with instrument air, take oil drum OMALA 300 bring to local clean up cap of oil drum check condition oil still ok. Do adjusment gap also add oil result ok. Test load cell response  with test weight result ok ( RIZAL & ANDRI & ADI )

Found polarity cable tacho backward. Make good connection polarity cable also tighten cable at motor do test run motor after install v-belt result ok. Test pfister feeder with load and no load result ok ( RIZAL & ADI & ANDRI )

Replace LCS, Done ( DADANG & RADIFAN ) 

Service sensor, reposition tube. Test from DCS result  ok ( RIZAL & ANDRI )

Repainting base plate with black color. Prepare nut for  motor, install motor ( MUHAIMIN & FIRMAN & AGUS & ADI & DADANG )