Check at local order of SG still open, service slide gate test open and close result ok. 453 BV1 connect unit at local. test open and close, result closed ok no error but when order open still error indication at CCR it is meaning solenoid valve to open is not touch. We think maybe mechanical problem when order pen some materials hold valve ( ADI & EVE RIZKY )

Fabrication belt drift for weight feeder at work shop ( PENY & FIRMAN )

Connected cable power input and cable heater to motor ( AGUS & ANDRI & EVE RIZKY )

PMR service analyzer. Clean up flange, probe, filter probe, sample line, diaphragm pump, filter balston, dryer gas from dirt of dust. Check humidity sensor and filter, replace filter if found bad condition with spare filter ( RIZAL )

PMR service medium and DC motor. Clean up area motor and filter motor. Measure vibration, noise and temperature free and load side motor. Add grease 15 times for free and load side motor ( PENY & EVE IQBAL )

PMR service medium voltage motor. Clean up area motor, filter motor. Measure vibration, noise and temperature free and load side. Add grease 10 times to 15 times for free and load side motor 363 FN1-363 FN2-423 FN1 and 443 FN1 ( ADI )

Trouble shooting for problem, result ok ( RIZAL & EVE IQBAL )

Fabrication support panel at work shop. Install panel lighting at ware house ( ANDRI )

PMR service medium voltage motor. Clean up area and filter motor. Measure vibration, noise and temperature free and load side motor. Add grease 10 times to 30 times for free side and load side motor ( AGUS )

Take data for TPM belong to RMK Nr1. Make data TPM AM, safety at computer save data ( YOGA & EVE DAVID )

WBI electrical and instrumentation area bottom blending, cooler and clinker silo. Measure vibration, noise and temperature free and load side motor. Check tank auto grease, result ok ( RIZAL & EVE IQBAL )

WBI electrical and instrumentation area top blending, pre heater, GCT, CT, kiln and burner floor. Measure vibration, noise and temperature free and load side motor. Check auto grease tank, some motor at low level need to be refill auto grease tank ( ADI & EVE RIZKY )

Installing auto grease for motor ( AGUS & FIRMAN & RIZAL & ANDRI )

Clean up filter 363 fA2. Clean up area, filter and carbon brush 363 MD1 from dirty dust ( YOGA & ADI )

Clean up area, filter and bearing motor of free and load side ( EMIS )

Check noise bearing motor at free and load side motor. Add grease 10 times to 30 times at free and load side. Result noise below 2 gE ( AGUS & FIRMAN )

Check safety device at 363 BC1 and noise bearing motor, add grease 25 times result noise below 2 gE ( RIZAL & ANDRI )

PMR service analyzer. Clean up flange, probe, filter probe, diaphragm pump from dirty dust. Replace seal for filter probe 2 at 443 2K1 result reading O2 decrease from 3.34 % to 2.54 % also replace connector sample line at diaphragm pump 463 2K1 result reading O2 decrease from 4.16 % to 3.26 % ( YOGA & ADI  )

Replace lighting lamp off with spare lamp. Test on lighting lamp result ok ( YOGA & FIRMAN )

PMR service medium voltage motor area kiln and coal mill. Measure vibration-noise and temperature free side and load side motor. Add grease 10 times to 30 times for free side and load side motor if found vibration > 4 mm/s and noise > 2 gE ( AGUS & EVE DAVID )

Pulling cable for purging from location sensor to panel I/O continue connected at I/O panel ( RIZAL & ANDRI & EVE IQBAL )

WBI are raw mill, feed bin and bag filter. Measure vibration-noise and temperature for free side and load side for some motor, screw, and rotary feeder that are not normal condition for vibration and noise. Area motor 333 AC1-333 AC2, 333 WF1 to WF4 are dirty form dust process need to be clean up area motor ( ADI & EVE RIZKY )

Change tank auto grease with spare unit ( ADI & EVE IQBAL )

PMR service analyzer L63 2k1, L63 2K2, L63 2K3 and 483 2K1. Clean up flange probe, sample line, filter probe, diaphragm pump, dryer gas, filter balston from coal dust. Check filter humidity sensor, replace filter with spare filter if found bad condition ( ADI & EVE IQBAL )

Replace valve kinetrol

Replace pressure transmitter

Replace temperature transmitter

Connected cable from sensor to temperature transmitter. Result reading at display temperature transmitter ok ( YONRI & ADI & SOBUR )

Continue prepare relocation

Replace Limit switch COG 2 eah

Relocation probe dan sample line

Prepare relocation probe thermocouple

Instal thermocouple ujung kiln

Service dan repair safety device,replace speed sensor

Clean up panel
Kalibrasi zero span

Clean up panel
Kalibrasi zero span

Check all solenoid purging
Replace all selang
Replace connector bocor

Download modifikasi program
Wiring control dan test run

Completing data PMR service analyzer at June-July 2024 for 463 2K1 & 443 2K1 also June 2024 for coal mill 

Kalibrasi fm 434 fm1 - 4

Check, service dan setting posisi dan indikasi damper

1. Clean up MCC (100%)
2. Clean up Switchgear (100%)
3. Clean up Transformer (100%)
4. LV Protection Relay Testing (95%)
5. LV Protection Relay Replacement (60%)

Complete data for TBM at shesig.sig.id for 3rd of meeting

Replace tank  auto grease with spare unit. Install at local set timer grease same with existing

PMR service analyzer coal mill, clean up flange probe, filter probe, sample line, diaphragm pump, filter balston, dryer gas from dust coal. Check filter humidity sensor, check filter replace if found bad condition with spare filter. Write data PMR service analyzer at form PMR service analyzer Coal Mill

Relokasi probe yg menghalangi

Replace thermocouple ujung kiln

Service solenoid aerasi cone blending timur,check dan service level material,check dan service shut off valve(434 SG1 SG2)

Scan data calibration pressure transmitter zero and span OH Nr2 save at computer D: Wahyu Adi T & Emis under name OH Nr2 calibration pressure transmitter 

Clean up area and filter motor from dust process use instrument air supply, check carbon brush condition result all condition ok. Add grease 10 time for free and load side at 463 MD1 ( PENY & ADI )

Clean up panel near L1C BC7 from dust coal use cleaning cloth and hand blower ( PENY & ADI )

463 2K1: found flow gas at 0 L/H CO: -0.15 PPM, NO: 25 PPM and O2: 20.90 %, clean up probe, filter probe from hard dust. Insert analyzer flow gas 100 L/H, all gas reading back to normal. 443 2K1: clean up flange probe, filter probe, sample line, diaphragm pump, dryer gas, filter balston from dust process, check filter humidity replace filter if found bad condition ( PENY & ADI & YOGA )

Service mcs dan prepare calibration mcs

Check service dan replace solenoid purging

Continue replace thermocouple Lt.6

Relokasi probe tubing pressure transmitter Lt.6

Readykan dan test run L3C RE1 setelah mekanik ada modifikasi

Continue replace thermocouple Lt.7 dan 8

Write data for calibration pressure transmitter area pre heater-kiln-raw mill-cooler and coal mill  ( ADI )

Replace tank of auto grease with spare unit. Refill existing tank auto grease at work shop ( EMS & ADI )

Calibration pressure transmitter zero and span area cooler and coal mill Nr2 get around 6 each ( YOGA & ADI )

clean up motor kiln,  fn7, 
analyser ph2 wiring

wiring di er4, tarik kabel

wiring, contineuty kabel, blackkout PLN

Replace thermocouple Lt.10 dan 11

Instal pressure transmitter Lt1 - Lt12

Calibration pressure zero and span transmitter area cooler and coal mill Nr2 get around 20 each transmitter ( YOGA & ADI )

Instal pressure transmitter lantai 12,11,10,9

Greasing gear motor,check open close kondisi masih OK

Replace bearing motor beck actuator,greasing gear motor,test open close

Calibration pressure transmitter for area coal mill and cooler for NR2 get around 30  ( YOGA & ADI )

Replace solenoid bray

Replace thermocouple

Replace selang angin
Test open close 
Clean up filter regulator

tarik kabel & terminasi

pasang solenoid , wiring

Calibration pressure transmitter zero and span area pre heater narogong 2 gets around 21 pressure transmitter for Over Haul  ( YOGA & ADI )

Cek motor posisi discouple
motor normal
vibrasi kemungkinan dari pompa lanjut tim mekanik

Install Indikasi run dan fault ke CCR
Test OK

WBI scissor lift

WBI trafo OTR 2, 3, 301, 302, A, B

Cek tegangan hilang, cek fasa ada, kemungkinan netral putus
harus bobok plafon untuk pengecekan lanjutan 

Ganti lampu area SDC building

cek breaker 6A trip beban termasuk AC
ganti MCB dari 6A ke 16A
test OK

Test open close,inject 4-20mA check indikasi
Clean up area damper

Replace broken solenoid valve 
Test function from Do

Dismantle all pressure transmitter area Preheater and id fan

Inspection electrical and welding tool of AQPA, SSM,CAT, TRUBA JAGA CITA, INDOPORLEN, RPM. Make report at form electrical for inspection electrical and welding tools for SHINAGAWA-TRUBA JAGA CITA-PINCURAN MAS-INDOPORLEN before 1 July 2024 ( ADI & EKA & MARPAUNG )

1. Clean Up MCC Room & Panel (100%)
2. Clean Up Switcgear Room & Panel (100%)
3. Clean Up Transformer (100%)
4. Clean up Capacitor & Panel (100%)
5. 364-MD1.M1 mesure capacitor (100%)
6. LV Protection Relay Tripping Test (100%)
7. LV Protection Relay Replacement (50%)

pabrikasi jalur kabel rtd 

Inspection electrical and welding tools of TOTAL PRIME ENGINEERING, TRUBA JAGA CITA, RPM ( EKA & ADI & MARPAUNG )

Making working permit area kiln and pre heater for Over Haul NR2 ( RIZAL )

Making working permit area raw mill and feed bin for Over Haul  NR2 ( YOGA )

Inspection electrical and welding machine from INDOPORLEN, TRUBA JAGA CITA and AQPA ( ADI & MARPAUNG TRUBA JAGA CITA & SUTRI TRUBA JAGA CITA )

Installing panel box at local ( PENY & ANDRI )

Completing data Juara Inovation and save at computer ( RIZAL )

Install panel lighting at area motor for heater motor. Connected cable power input and install cable heater motor ( YOGA & FIRMAN & ANDRI )

Preparing data of project, pulling cable, install LCS and I/O MCC to vendor ( PENY )

Completing wiring for Input and Output panel ( AGUS )

Clean up panel lighting and welding from dust coal use hand blower and cloth 

Service grinding machine from mechanic I., test functional result ok. Give tagging blue color ( ADI & FIRMAN )

Prepare document for audit ( YURIZAL )

Labelling Input Output Panel ( AGUS )

Prepare box at work shop, Install support panel continue painting  ( PENY & ADI )

Installing lamp ( ANDRI & FIRMAN & EVE DAVID )

Install strainer line for instrument air ( FIRMAN & ANDRI )

Inspection electrical and welding machine for Mechanic NR 1 ( ADI & EVE DAVID )

Wiring diagram I/O panel ( AGUS )

Install receptacle at IDO PUMP ( ANDRI & FIRMAN )

WBI instrumentation and electrical are Coal Mill-Reclaimer and Tripper Coal ( PENY )

Replacing contactor auxilary LCS ( YOGA & EVE RIZKY )

Installing lighting panel and receptacle ( ANDRI & FIRMAN )

Completing data for presentation JUARA INOVASI ( RIZAL )

Completing data check sheet for PMS 463 MD1 years 2024. Scan file and save at server ( EMIS & ADI )

PMR service analyzer such clean up probe, filter probe, diaphragm pump, dyer gas, filter balston. Check filter humidity sensor replace filter if found bad condition with spare filter ( AGUS )

PMR service analyzer such clean up probe, filter probe, sample line, diaphragm pump, filter balston, dryer gas Check filter humidity sensor replace filter if found bad condition with spare filter ( YOGA & EVE RIZKY )

Replacing panel lighting and installing receptacle ( ANDRI & FIRMAN )

PMR service CEMS, clean up filter purge air unit dust hunter and flowsic also area motor, transducer A & B flowsic, swivel window t/r & reflector dust hunter also alignment, filter cabinet MCS 100 E, room of CEMS and span gas also H2 of room ( YOGA )

PMR service medium voltage motor. Clean up area and filter motor, measure vibration, noise and temperature free and load side. Add grease 10 times to 15 times for free side and load side motor ( PENY )

PMR service medium voltage motor, clean up area and filter motor. Measure vibration, noise and temperature free and load side. Add grease 10 times to 30 times for free side and load side motor ( AGUS )

Installing timer for lamp every tent over haul, test functional time result ok  ( FIRMAN & ANDRI )

Repair/ganti panel junction transmitter (Rizky, Deden)

Inspeksi Tools truba Dan tagging tools Truba (Eka)

Cek motor slide gate (info motor terbakar), cek motor aman, lepas couple ampere motor normal, (indikasi gate berat), ganti/r pair emergency dan push button (Rizky, Yana)

Pindahkan motor, (Hariyanto, Amun)

Lanjut Cek/replace kabel FO (Titok,Deden)

Inspeksi Tools Civa, Area Workshop Civa
(Yana, Eka)

Inspeksi Tools dan Taging tools Civa 
Area Blending PH, Rawmill 
(Rizky, Hariyanto)

Lanjut pengecekkan kabel FO (Titok, Deden)

Cek Backfilter (Yana)

Ganti lampu TL, no 2,3,7,8,10,11,19 dari belakang (Rizky)

Clean up motor dan panel LCS (Rizky, Supriadi Eve)

Completing data check sheet WBI grounding and lightning 2024 and scan file save at server ( EMIS & ADI )

Completing data wiring I/O panel ( AGUS & PENY )

Completing data TPM for AM, safety and focus improvement also print out file put at dash board . Do house keeping at local ( YOGA & RIZAL & EVE RIZKY )

Recondition motor Ex 393 SC6, installing cover fan for blower portable ( ANDRI & FIRMAN )

Replacing grease tank of AUTO Lubrication with maximum level grease. Refiiling low grease tank to maximum level grease at work shop ( PENY & ADI )

394CV2/3/4, 394 RF2/3/4
LCS kotor, clean up panel LCS (Rizky, Supriadi Eve)

Motion sensor abnormal, cek  kontrol motion (Yana)

Kabel FO Abnormal, relokasi kabel FO (Titok, Deden)

Motor bearing kasar, bongkar motor, ganti bearing, instal motor (Hariyanto, Eka, Amun)

PM reclaimer coal check proximity Harrow, clean up LCS, clean up others instrumentation sensor ( RIZAL & EVE RIZKY )

PM reclaimer coal replace harrow cable and control also change roller position ( AGUS & PENY & ANDRI & FIRMAN )

PM reclaimer coal clean up panel room from coal dust process use hand blower ( YOGA & IMAN )

Completing data check sheet WBI panel grounding, welding and lighting year 2024 continue scan also save data at server( ADI & EMIS )

Bongkar panel tidak terpakai (Rizky, Anton, Eka)

Relokasi transmiter (Titok, Deden)

PMR Service Critical Motor dan Elinst area Rawmill (Hariyanto)

Clean up motor dan panel LCS (Rizky)

Clean up body motor from dirt of dust use instrument air supply and equipment cleaning tools ( FIRMAN & ANDRI )

WBI top blending, CT, PH and KILN. Clean up motor use cloth from dirt of dust ( PENY & EVE RIZKY )

PMR service analyzer, such as clean probe, filter probe, sample line, diaphragma pump, filter balston, dryer gas. Check filter humidity sensor replace if found bad condition ( RIZAL )

PMR service analyzer, such as clean up probe, filter probe, sample line, diaphragma pump, filter balston, dryer gas from dirt of dust. Check filter humidity sensor replace with spare if found bad condition ( AGUS )

WBI area feed bin, RM, CT and 423 BF1. Clean up area motor from dirt of dust process use instrument air supply ( YOGA )

Completing data check sheet WBI 363 RM1 of Feed bin-Raw Mill-CT-Bag Filter years 2023 ( EMIS & ADI)

Clean up motor dan panel LCS (Rizky)

Dismantle lamp of 473 north side and replace lamp test lamp result on ( FIRMAN & ANDRI )

PMR service CEMS. Clean up filter purge air unit  dust hunter and flowsic 100, transducer A & B flowsic 100, swivel window T/R & R dust hunter also alignment dust hunter. Clean up CEMS room and filter dust cabinet ( RIZAL & EVE RIZKY )

PMR service medium voltage motor. Clean area and filter motor from dirt of dust use instrument air supply. Measure vibration-noise and temperature free and load side motor. Add grease 30 times and 15 times for FS & LS motor ( AGUS )

Completing data sheet WBI and PMR year 2023 and 2024, continue scan safe at server computer ( ADI & EMIS )

PMR service elevator, clean up room of elevator and cage. Test functional elevator from 8th to 1st floor. Result good ( PENY & YOGA )

Service lampu area GCT (Titok, Deden)

Ganti socket 1 Phasa panel welding area Preheater (Anton)

Check, dan clean up coating sensor Level Material Blending Silo Timur dan Barat (Rizky, Yana)

Ganti lampu selancar area 4D4 (Hariyanto, Anton)

Ganti Probe IKGA (Yana)

PMR Service Critical Motor Coalmill (Hariyanto)

Completing data check sheet PMR  IR TAD-CCTV-T Scanner, Pyrometer and PM 363 MD1. Continue scan also save at computer ( ADI & EMIS )

Replace burned motor with spare motor ( FIRMAN )

Test run motor and put at ware house for motor ( RIZAL & YOGA )

Connection cable panel I/O ( PENY & EVE RIZKY )

Clean up and replace carbon brush ( AGUS & ANDRI )

PMR Service Steck Cooler (Titok)

Clean up Motor dan panel LCS (Rizky)

Clean up Motor dan panel LCS (Rizky)

Ganti lampu atas Panel Liquid (Anton, Eka)

WBI Electric dan Instrument Reclamer dan Coalmill atas (Rizky)

Make data sheet and completing check sheet calibration damper and speed ( YURIZAL )

Replace motor blower with spare motor for yellow motor blower ( MUL )

Completing data sheet PMR service medium voltage motor ( ADI )

PMR Critical Motor dan Elinst RawMill (Hariyanto)

PMR service analyzer such as clean up probe, filter probe, diaphragm pump, filter balston, dryer gas from dust of coal. Check filter humidity sensor replace if found bad condition with spare filter ( YOGA & EVE RIZKY )

Connect cable at I/O panel and install solenoid valve ( PENY & MUL & AGUS & ANDRI )

WBI Welding Panel dan Lighting Area Preheater (Yana)

WBI Elinst Clinker Silo dan Coalmill Bawah (Rizky)

Clean up Motor dan panel LCS (Rizky)

Service CEMS (Rizky, Deden)

Lanjut Fabrikasi Panel dan Service Vacum dari ER4 (Hariyanto, Amun)

Service Lampu area Pister Feeder (Anton, Eka)

Service Analyzer AN1 dan AN2 (Yana, Deden)

Clean up Motor dan panel LCS (Rizky)

Clean up Motor dan panel LCS (Rizky)

Clean up Motor dan Panel LCS (Rizky)

Clean up Motor dan panel LCS (Rizky)

Termination cable at I/O panel and solenoid valve ( PENY & ANDRI )

Repair door of elevator at 1st floor service limit switch for door. Test run elevator functional from 8th to 1st floor result ok ( AGUS & EVE RIZKY )

PMR service IR TAD, CCTV, T scanner, Pyrometer such as clean area equipment, lens, probe from dirty dust process ( YOGA )

PMR service analyzer. Clean up probe, filter probe, sample line, diaphragm pump, filter balston, dryer gas from dirty dust. Check filter humidity sensor replace filter if found bad with spare filter ( RIZAL )

Check rubbish bin at local, bring bad rubbish bin to scrap room of environment department. Bring god bin to local and make name of rubbish bin for RED-GREEN and YELLOW ( ADI & EMIS & CIVACON MUL )

Completing data check sheet PM 363 MD1 and PMR service mv motor and pyrometer 

Cek Analyzer (Yana)

Fabrikasi oli rel Lift (Yana)

Lanjut Fabrikasi Panel LBS
(Amun, Hariyanto)

PMR Critical Motor dan Elinst Kiln
(Hariyanto)

Cek Camera baru Burner,
Ganti lampu area Burner,
Ganti lampu area Cooler
(Titok, Deden)

Clean up Motor dan panel LCS (Rizky, Anton, Eka)

Clean up Motor dan panel LCS (Rizky, Anton, Eka)

Ganti lampu selancar atas pintu Rawmill (Rizky, Anton, Eka)

Ganti lampu selancar, (Rizky, Anton, Eka)

Pulling cable solenoid valve and LCS, connect cable motor and LCS ( PENY & ANDRI & FIRMAN )

PMR service CEMS. Clean up filter purge air unit for dust hunter and flowsic. Clean up transducer A and B flowsic, swivel window T/R and R dust hunter also alignment dust hunter, clean up CEMS room, and filter cabinet MCS 100 E ( YOGA )

PMR service medium voltage, clean up area and filter motor. Measure vibration-noise and temperature free side and load side, add grease from 10 times to 30 times for free and load side motor if found vibration > 4 mm/s and noise > 2 gE ( AGUS )

Completing data check sheet PM 363 MD1 and PM Weigh Feeder ( ADI & EVE RIZKY )

Prepare plate, dan fabrikasi panel LBS (Hariyanto,Amun, Anton)

Bongkar motor, Ganti bearing motor, instal motor (Hariyanto, Amun, Anton)

PMR Service (Yana)

Ganti lampu (Rizky, Deden)

Ganti lampu (Rizky, Deden)

Ganti lampu (Rizky, Deden)

PMR Critical Motor dan Elinst Rawmill (Hariyanto)

Cek all Safety Device area Feedbin dan Rawmill (BC,WF),  croscek WF (Anton,Eka)

Cek indikasi Ready BD (Yana, Davin EVE)

Ganti lampu dan tes sump pump (Yana, Deden)

Cek CO2 system (Titok,Eka)

Clean up CEMs room dan ER 4 area genset kotor (Anton,Amun,Deden)

Clean up panel (Rizky)

Bongkar lampu (Rizky)

PMR MCC Load (Rizky)

WBI inspection (Rizky)

Bongkar panel (Rizky)

Clean up panel (Rizky)

Clean up panel dan instal kanopi (Rizky,Amun, Ahmad EVE)

Clean up panel dan instal kanopi (Rizky,Amun,Ahmad EVE)

Pasang kembali tutup fan motor (Rizky,Ahmad EVE)

Clean up dan tutup panel (Rizky,Ahmad EVE)

Ganti lampu (Rizky, Ahmad EVE)

Ganti lampu (Rizky,Ahmad EVE)

Clean up panel dan kasih kanopi (Rizky,Amun)

Repair support tiang LCS (Rizky,Amun)

Repair support tiang LCS (Rizky,Amun)

SV Purging 1 dilepas, tunggu order, sementara pakai Purging 2 (Yana, Rizky)

Ganti roller dan list pintu (Yana, Rizky, Deden)

Replace solenoid valve and pressure switch. Prepare canopy for pressure switch continue install at local ( RIZAL & ANDRI )

PMR service medium voltage motor, clean up area and filter motor from dirty use instrument air supply. Measure vibration-noise and temperature free and load side motor. Add grease 10 to 15 times for free side and load side if found vibration > 4 mm/s and noise > 2 gE ( PENY )

Prepare canopy of LCS. Install LCS at local  ( YOGA & FIRMAN )

Completing data check sheet WBI 

pulling cable from bottom CT to ER3 ( ALL crew )

Disconnect sambungan untuk AC
Pulling kabel baru khusus untuk AC 
Connect ke MCB dan stop kontak AC
Test OK

Perbaikan cubicle MCC
Ganti MC dari ABB 80A ke LS 100A
Ganti MCCB dari ABB ke Schneider, buat lubang dudukan baru
Ganti kabel out MCCB ke MC

Clean up panel control and PLC tripper from dirty coal dust ( RIZAL & EVE RIZKY )

Clean up motor brake, area motor and panel from coal dust process. Install lamp 1 each test on result ok ( PENY & FIRMAN )

Clean up rail cable and tray also all panel at south side from coal dust process with instrument air and hand blower ( AGUS & ANDRI )

Test functional water spray, at L1C BC7 found contact solenoid valve is not function well, replace limit switch with spare test functional result ok. L1C BC5 test functional found stick flapper is not long enough, replace stick flapper with spare test functional result ok ( YOGA & ADI )

Ruangan induksi di akses kontrol AC tidak bisa dinyalakan bareng (2Ea AC)
Cek MCB untuk 1 ruangan (2 AC, lighting ruangan dan TV)
Preparing jalur kabel untuk tarikan baru

Cek piston load unload belum buka
cek tegangan di socket solenoid 0 Vac
cek dipanel kontrol kabel untuk solenoid lepas diterminal
perbaikan kabel dan kencangkan terminasi
test run ok

Test run motor and service motor ( PENY & AGUS )

Fabrication canopy motor ( FIRMAN & ANDRI )

Check pressure switch at local compare with CCR ( RIZAL & YOGA & Production & MUKLAS )

Completing data PMR analyzer check sheet ( ADI & EVE RIZKY )

Repaire and replace bearing motor also clean up motor 30 KW ( FIRMAN & EVE RIZKY )

PMR service analyzer, such as clean up probe and flange, filter probe, sample line, membran pump, balston filter, dryer gas. Check filter humidity, replace filter if found bad condition ( RIZAL )

Install AUTO lubrication ( PENY & ANDRI )

PMR service CEMS, such as clean up filter purge air unit dust hunter and flowsic 100. Clean up transducer A & B Flowsic 100 and swivel window transducer and reflector also reflector Dust Hunter. Clean up CEMS room and gas botle gas room also filter cabinet MCS 100 E ( YOGA )

PMR service medium voltage. Clean up area and filter motor. Measure vibration, noise and temperature free and load side motor. Add grease 10 times to 30 times for free and load side motor ( AGUS )

Rapihkan drum oli (pindahkan dari OTR A ke Trafo OTR B)
Clean up Area Trafo dan MSS

Commisioning dan Test Run
Pressure 5,7 Bar
Cek tegangan input kompresor 373 Vac
Cek Arus Input kompresor 300 A

Clean up ceceran oli di lantai dan body genset
Perbaikan kebocoran oli pada baud dengan threebond dan bold tightenning

Tie in Kabel Input breaker cubicle MCC ke Bar
Pasang scun kabel tarikan LCS ke Kompresor
Connect kabel di LCS dan di terminal input kompresor

Completing data wiring I/O of raw mill and preheater ( AGUS )

Service analyzer, found valve safety relief late work when energize ( RIZAL )

Replace lamp that are off with new spare lamp. Test on result ok ( ANDRI & ENDEN )

PMR service critical motor and LSR. Clean up area and filter motor, measure vibration-noise and temperature free and load side motor. Add grease from 5 times to 10 time for free and load side if found vibration > 4 mm/s also noise > 2 gE ( PENY & ADI & EVE RIZKY )

Cek panel MCB kontrol trip
ada bau coil MC overheat
ganti main MC, test simulasi saat pindah ke delta MC delta tidak energize
preparing lubang dudukan semua MC
ganti semua MC dari Schneider ke LS
kabel motor cooling fan dan kabel input untuk kontrol ada indikasi overheat di tapping input MC delta
ganti kabel input motor cooling fan dan rewiring kabel input kontrol
test run OK

Preparing kabel 240 mm
preparing kabel 95 mm
pabrikasi kabel tray LCS ke Kompresor
Install kabel tray
pulling kabel 240 mm lcs ke kompresor
ganti breaker cubicle MCC dari 400 A ke 680 A

Lampu jalan area trucklift sampai arah reclaimer batubara mati
ganti lampu 4 tiang
test OK

COmpleting data wiring panel for I/O ( AGUS & PENY )

Inspection electrical and welding tools. Repaire cable extention cable, portable lamp, grinding machine, drilling machine, and cutting machine full fill standard company ( ADI & YOGA & EVE RIZKY )

Replace bearing motor ( RIZAL & ANDRI & FIRMAN )

Tambah lampu penerangan 

Bongkar Lampu (Untuk di Repair)

Bongkar Lampu (Untuk Di Repair)

Clean Up Motor dan kasih Kanopy (Penghalang)

Ganti Socket Legrand Panel

Ganti Lampu

pulling cable profibus ( ANDRI )

PMR service analyser such as clean up probe, sample line, filter probe, membran pump. balston filter, dryer gas from dust coal ( RIZAL & YOGA )

Dismantle motor and bring to work shop ( PENY & ADI & FRIMAN & ANDRI )

Preparing spare motor ( PENY & ADI & FIRMAN & ANDRI )

Check at local, do refilling grease and change battery for auto gun grease ( AGUS & EVE RIZKY )

Move cable I/O ( RIZAL & YOGA )

Accompany judge for assesment TPM at work shop and local area ( YOGA & RIZAL )

Replace lamp that is off. Test on result ok ( AGUS & FIRMAN )

Check draft at local compare at CCR ( RIZAL & YOGA & EVE RIZKY )

WBI electrical and instrumentation ( PENY & EVE RIZKY )

Inspection electrical and welding tools. Repaire cable power electrical tools such as drilling machine, extention cable, portable lamp. cutting machine to company standard ( ADI & ANDRI )

* Cek lampu jalan area trucklift

* Cek lampu jalan area office afr sebelah trucklift

* Indikasi sensor air filter bintang-bintang

* Indikasi DP separator bintang-bintang

Clean up area motor stator and rotor use special liquid, replace bearing 6206 2 each and 6303 1 each. Install back al local ( PENY & ANDRI & FIRMAN & ADI )

PMR service analyzer such as cleaning probe, filter probe, membran pump, filter balston, dryer gas, sample line from dirty ( YURIZAL )

Completing data TPM and prepare basket cage for equipment cleaning tools also painting green color ( YOGA & EVE RIZKY )

PMR service medium voltage motor, clean up area and filter. Measure vibration-noise-temperature at free and load side. Add grease 20 to 30 times for free and load side if found vibration up to 4 mm/s and noise up to 2 gE ( AGUS )

Inspection electrical and welding tools. Repaire cable for extention cable, grinding machine, cutting machine, drilling machine ( ADI & FIRMAN & ANDRI )

Complete data absention, AM, safety and Focus Improvement and theme ( PENY & YOGA & YURIZAL )

PMR service CEMS, such as clean up filter purge air unit, transducer A & B, swivel window T?R & R alignment dust hunter, room CEMS and bottle gas ( RIZAL )

PMR service medium motor, clean up area and filter motor.  Measure vibration-noise and temperature for free and load side, add grease 10 to 15 times at free and load side motor ( AGUS )

WBI Trafo MV OTR 2, 3, 301, 302, A, B

Cek kontaktor lengket
cek motor ground
discouple dan disconnect kabel power motor
bawa ke workshop untuk perbaikan (rewinding)
drawout cubicle mcc bawa ke workshop untuk perbaikan

Install motor di lokal 
(setelah service rotor dan stator karena karat, ganti bearing 2 x 6214 zz, ganti cooling fan karena rusak, retapping lubang untuk baud kabel ground dan cover, perbaikan dudukan cover fan)
test putaran motor
cek arus noload  fasa R=34 A; S=36 A; T=37 A

Discouple dan disconnect kabel power motor
bawa ke workshop
bongkar motor, coil motor basah
panaskan motor dengan heater

Cek resistan coil motor OK
Cek resistan isolasi motor OK
Cek induktansi motor unbalance nilainya
buka cover motor bau coil motor overheat
discouple motor dan disconnect kabel power
bawa ke workshop untuk di rewinding

Test run setelah rewinding motor
Balik arah putaran main motor
test run
cek tegangan saat kompresor unloading 350 Vac balance

Clean up area 5R, install guarding shell cooling fan and  sign safety ( ALL Crew Electric )

Clean up filter and electric room , top panel medium voltage and top panel trafo at ER5. Clean up include inside MCC and ACB ( IMAN & FIRMAN )

WBI area KILN, COOLER, BURNER FLOOR, and CLINKER SILO ( YOGA & EVE RIZKY )

WBI top blending, CT, Pre heater, and KILN ( PENY )

Inspection electrical and welding tool of PPUP work shop ( ADI & ANDRI )

Check electrical and welding tools, do some repaire cable for welding machine, extention cable, grinding machine, portable lamp because grounding cable are not connected ( ADI & FIRMAN & ANDRI )

WBI electric and instrumentation ( PENY )

PMR service analyzer such as. clean filter probe, probe, membran pum, filter baltson , dryer gas, filter humidity sesnor from dirt ( YOGA & EVE RIZKY )

PMR service CEMS such as clean up filter purge air unit, transducer A & B, swivel windows dust hunter ( YOGA & EVE RIZKY )

Test gas NO ( YOGA & EVE RIZKY )

Replace vibration sensor. measure vibration at local compare with CCR ( AGUS & ANDRI )

Replace cable power motor, connect cable at LCS and motor, test run measure ampere motor result ok ( PENY & ADI & FIRMAN )

Ganti lampu sorot LED 2 Ea
Test OK

Wiring kabel di panel PLC dan cubicle MCC
Pulling kabel dari LCS M04-WP8 ke M04-WP7
Pulling kabel dari LCS M04-WP7 ke Sensor
(kabel spare hanya ada 1 core di tiap LCS)

Ganti lampu dari HPIT ke Lampu LED 200W 1 Ea
Test OK

CCTV area pompa M04-WP1 s.d. 4 mati
Cek socket basah karena air hujan, ganti socket RJ45
install juction box
masukkan kabel ke juction box
test OK

Coba clean up masih sama
coba ganti converter balun masih sama
coba lepas camera pasang lansung di DVR OK
kemungkinan kabel sudah rusak
preparing ip cam dan ukur kebutuhan kabel ethernet

WBI Trafo MV OTR 2, 3, 301, 302, A, B

Prepare pipe also make drut pipe( ADI & ANDRI )

Replace v-belt, service l/s from 1st to 8th door ( PENY & FIRMAN )

PMR service IR TAD temperature, CCTV, T scanner and camera burner. Clean up lens and probe ( RIZAL )

PMR service medium voltage motor. Clean up area and filter motor, measure vibration-noise-temperature load and free side. Add grease 10 time to 20 times if found vibration > 4 mm/s also noise > 2 gE ( AGUS & EVE RIZKY )

PMR service medium voltage motor. Clean up area and filter motor, measure vibration-noise and temperature fix and load side motor. Add grease 5 time until 15 times if found vibration up to 4 mm/s and noise up 2 gE ( YOGA )

Install Grounding Rod, cek resistan 1 ohm
pulling kabel panel distribusi ke grounding rod
connect kabel di panel dan grounding rod
Perapihan kabel

Clean up area SGA Tyre 3 from dust use equipment cleaning tools and instrument air supply. Also tidy up cable shell cooling motor cable at cable tray (ALL CREW ELECTRIC NR1 )

Pasang Grounding rod baru (1 batang 4m)
Cek dengan earth tester masih tinggi 5.9 Ohm

Install LCS for roll machine ( FIRMAN & ANDRI )

Adjust tilt sensor position ( RIZAL & EVE RIZKY )

Monitor functional analyzer ( RIZAL & EVE RIZKY )

WBI Hoist Crane ( PENY )

Replace s/v test functional result ok ( YOGA )

Clean up area motor and filter.add grease if found vibrationg and noise abnormal ( AGUS )

Clean up filter fan an front of ER6, also clean up room of electric rooms and top panel MV and trafo ( ADI & IMAN )

Ganti Lampu TL 14 Ea
Ganti Lampu Ulir 3 Ea
Ganti lampu tembak 100W 2Ea
Ganti lampu selancar 1Ea

Breaker trip saat pindah ke kontaktor delta
Cek resistan coil dan isolasi main motor dan motor fan OK
Cek finger contactor OK 
Cek tegangan output contactor (posisi kabel ke motor disconnect) balance 390 Vac OK
Cek setting MCCB di MCC, rubah Io dari 630 A ke 400 A dan Isd dari 1.5 ke 5
Test Run OK

 fabrication box grease for bucket elevator ( AGUS & EVE RIZKY & MADIN )

WBI camera burner and clinker silo ( PENY )

Clean up s/v for water and air, found many dirty inside membran s/v water. result test ok ( RIZAL & ANDRI )

Install sensor RTD and vibration ( RIZAL & ANDRI )

PMR service CEMS, such as clean up transducer A & B flowsic 100, clean up swivel window dust hunter, clean up filter purge air unit, calibration zero and span FIDOR ( YOGA & ADI )

Coba kencangkan baud contactor dudukan kontak finger patah karena sudah getas
Buat lubang dudukan untuk kontaktor
Ganti contactor delta dari schneider ke LS
Ganti kabel jumper untuk Output MC Delta dan Star, karena kabel existing sudah overheat
Test OK

Install External Fan untuk pendinginan main motor
Wiring kontrol untuk start stop motor fan
Test OK

Clean up area HRG and filter use hand blower  ( JAJAT & ADI )

Clean up area motor and filter motor, Check carbon brush condition result condition carbon brush are ok ( AGUS & EVE RIZKY )

Clean up area motor and filter motor from dust, check carbon brush condition. Result carbon brush condition are ok ( PENY & FIRMAN )

Replace load cell for 453 PF1 continue calibration zero and span pfister feeder. Check calibration zero and span 483 PF1 ( RIZAL & YOGA & ANDRI )

Clean up panel I/O west and east blending from dirt of dust blending with hand blower, also clean up panel FM and PF inside east blending ( ADI )

Clean up panel I/O from dirty dust with hand blower ( ADI )

Cek LCS handle patah
Cek Posisi LCS masih OFF
ganti handle LCS
On kan LCS
Test Run OK

Cek arah putaran motor terbalik
Balik putaran motor dengan menukar kabel fasa S dan T\
Test Run
OK

Cek sensor, clamp sling menyentuh dinding lubang sensor
perbaikan clamp sling sensor high dan low
Clean up sensor high dan low
buat lubang baru untuk baud dudukan sensor
adjust sensor di posisi tengah tengah lubang
Test OK

Install dudukan sensor
Relokasi sensor
Test
OK

Regreasing main motor

Regreasing main motor

Regreasing main motor

Regreasing main motor

Regreasing main motor

Connect motor RF and load cell at 483 PF1 ( PENY & YOGA )

Connect new TU at panel I/O, install RTD and vibration sensor ( RIZAL & ANDRI )

Repaire TLS for 493 AC1,AC2,AC3 ( PENY & YOGA )

Prepare cable power of hoist, connect power of hoist ( AGUS & FIRMAN )

Connect cable for limit switch and solenoid valve at I/O panel also box termination ( RIZAL & EVE RIZKY )

Prepare cable for camera, connect cable at side. Test run camera result view ok ( PENY )

Install rell hoist at 463 MD1 ( FIRMAN & CIVACON )

Install 2 each blower motor, prepare cable blower motor at  work shop continue connect cable blower motor. Test run blower blower, replace contactor for run and emergency stop ( AGUS & YOGA & ADI & IMAN )

Regreasing main motor

Regreasing main motor

Regreasing main motor

Regreasing main motor

Regreasing main motor

Preparing relokasi sensor
install conduit dan pulling kabel

Connected cable welding incoming to ER4 near 463 KL1 ( AGUS & FIRMAN )

Test run motor spare result ampere high around 15 A. Take house motor after rebushing at work shop mechanic. Install motor test run with no load result ampere 2.4 - 2.6 A ( YOGA & PENY & ADI )

Do test run motor with CBM teams, 1st result vibration and noise are still high upnormal, retightening coupling motor measure vibration and noise result normal when speed 2000 RPM ( PENY )

Install box terminal cable for power and indication, also limit switch and solenoid valve and cable tray and pipe cable from limit switch  ( RIZAL & EVE RIZKY & ANDRI )

Lanjutan
Tightenning bold di LCS dan MCC
On kan Breaker
cek tegangan di LCS
OK

Install motor setelah rekondisi dan rewinding
Install dan tightenning kabel power di motor dan MC 

Install for new LCS ( PENY & AGUS & YOGA )

Prepare support for box termination and limit switch and solenoid valve. Install box termination at local and  limit switch and solenoid valve. Painting support with yellow color ( RIZAL & ANDRI )

Install pipe for cable power hoist. Install cable hoist from motor to LCS. Test run hoist result ok ( FIRMAN & EVE RIZKY )

Do check rubber coupling. Tightening nut for coupling distance more close than before ( AGUS )

Take motor from ware house. Test run at work shop result is not good, MC power supply trip and litle smoke come out from motor. try install hose new spare motor to original motor but does not match with nut. Original motor do rebushing at work shop mechanic  ( PENY & ADI & YOGA )

Doubling kabel existing dengan kabel Ex 443-CX1

WBI trafo MV OTR 2, 3, 301, 302, A, B

Housekeeping pindahkan drum oli ke gudang limbah B3 dan oli baru ke MSS

Replace bearing 2 each. Install bask shaft motor and motor. test run motor, measure vibration and noise result vibration free and load side are ok. Noise for free side around 1.9 gE and load side 2.6 gE. Add grease for measure noise still high up 2 gE for free side and load side  ( PENY & EVE RIZKY & YOGA & FIRMAN )

Take cable indication and power for limit switch and solenoid valve at ware house electric around green cable 35 meter and black cable 100 meter. Pulling cable from site slide gate CKD to panel i/O at 363 FN2. Prepare box termination cable at work shop ( RIZAL & ADI & ANDRI )

Install panel kontrol kompresor
Install display controller
Install Emergency pushbutton

Test run setelah recharging
OK

rewiring control kompresor
simulasi dengan display kontroller

Cek baterai, skun baterai kendor disisi kabel jumper
ganti skun/clamp 
recharge baterai

WBI dan tes run genset nar 1, nar 2 dan packhouse nar 2
genset nar 2 kiln tidak bisa di start

WBI Trafo MV OTR 2, 3, 301, 302, A, B

Dismantle motor 483 FA1 M1, dismantle bearing motor and clean up around body motor from dust shaft motor from grease  ( PENY & ADI & FIRMAN )

Replace card analog with new card. Test run from CCR, set 0 % actual already close but indication available, set 100 % actual open full but indication 70 % ( RIZAL & ANDRI )

Install support panel
Wiring kontrol panel kompresor

Lanjutan
Cek valve solenoid EX Kompresor valve jenis NO
sedangkan valve gantinya jenis NC
Modifikasi wiring dengan menambah relay dan coil solenoid lewat kontak NC relay
Test Run OK Normal

Pabrikasi support untuk panel kompresor
pulling kabel LCS to MC

- Install display kontroller di kompresor
- Install trafo kontrol 380V-220V-24V
- Cek wiring MC ada kesalahan wiring seharusnya kontak NC MC delta untuk terminal A2 
   MC Star dan kontak NC MC Star untuk terminal A2 MC Delta, Koreksi wiring
- Test simulasi tanpa beban motor OK
- Pasang kabel motor test run, kompresor run
- Saat loading fuse kontrol putus
- Cek kabel solenoid ada kabel yg lepas dari terminal soket dan short, perbaikan kabel dan
  ganti soket
- Ganti solenoid+valve karena posisi coil diganjel baud
- Cek indikasi pressure out kompresor tidak naik, Ganti sensor pressure Test run OK
- Kompresor kadang kadang high temperatur, cek kabel RTD ada sambungan yang kadang
  kadang short, perbaikan kabel 
- Saat starting putaran motor berat....... lanjut

Pull back kabel LCS to MC
Buat 2 lubang di panel untuk exhaust fan dan sirkulasi udara

Lanjutan
Coba ganti Trafo
Tes run
kondisi MC masih tidak bisa ON
Lepas display kontroller, simulasi di workshop
test simulasi OK 

cek tahanan gulungan motor dan tahanan isolasi OK
cek fuse input dan output trafo putus, ganti fuse 
simulasi tanpa beban motor
MC star dan mc delta abnormal (kadang energize kadang tidak) saat distart
trafo kontrol berasap

Connected cable welding to ER4 ( AGUS & YOGA & FIRMAN)

Replace bearing 2 each for agitator, install motor at local ( PENY & ADI & ANDRI & GEMAN )

Ganti Lampu TL LED 8 Ea

cek grounding panel hasil 10 ohm
kabel grounding hanya sampai panel lama, tidak ada grounding rod

Pengambilan sample oil trafo OTR-A dan OTR-B by quadro

WBI dan test run genset Nar 1 dan packhouse nar 2

Ganti lampu TL ulir 2 Ea ruangan SI Electric

Ganti lampu TL LED 2 Ea

Relokasi kamera CCTV 1 Ea

Install main motor kompresor
Wiring panel kontrol

WBI Trafo MV OTR A, B, 2, 3, 301, 302

Install kamera CCTV 4 Ea dan MMC 2 Ea

preparing kabel LCS to MC dan MC to motor

cek grounding komrel office 3 titik
nilai resistance dibawah 5 ohm
OK

Cek display kontroller Ex kompresor 66B-CX3
display blank karena ada komponen overheat di PCB mainboard

Service sensor DP separator Ex kompresor D34-CPA

Ganti lampu jalan 8 Ea
resetting timer karena penunjukkan jam sudah bergeser
test OK

cek lokal fan radiator trafo trip 5 Ea dan noise 1 Ea
disconnect kabel dan lepas motor 6 Ea bawa ke workshop

Perapihan kabel
tambal bekas bobokan beton

Replace cable incoming welding that is burned to ER4 near 463 KL1 with spare cable ( AGUS & FIRMAN )

Replace seal for L93 RF1 and replace bearing 6208 2Z 2 each for L93 SC5 ( PENY & HARYANTO & RAMA & ANDRI )

Prepare dash board for TPM 463 KL1 Trye 3, make report for FA, AM and Safety. Print out report and laminating. Install report at dash board ( YOGA & RIZAL & ADI & EVE RIZKY )

Clean up panel drive at ER4 and make report for precomissioing drive ( PENY )

Info shift motor cooling fan 1.1 OL disconnect kabel power
cek ulang tahanan coil motor dan tahanan isolasi OK balance
cek nilai induktance OK balance
coba reconnect kabel test ampere 2,8A, setting eocr 2.75
naikkan setting eocr ke 3A 
test run OK

Open phase muncul saat pindah ke MC delta
cek timer star 15s rubah ke 10s
cek parameter open phase 10s rubah ke 3s
test OK

Cek kabel kemungkinan ada yang putus
pulling kabel baru dari Luar MSS building ke lampu jalan
test OK

Pulling cable for indication temperature motor ( AGUS & EVE RIZKY )

Pulling profibus cable for new filed I/O ( RIZAL & ANDRI )

Install cable for vibration and RTD ( RIZAL & ANDRI )

Move cable power from L93 RF3 to L93 SC4 also connected cable to L93 SC4. Test on result ok ( YOGA & AGUS & ADI & FIRMAN )

Check motor 463 MD1 at ware house ( AGUS )

Pulling cable power, but we find spare cable at L93 RF3 ( YOGA & PENY & EVE RIZKY & FIRMAN )

Install sensor RTD and vibration ( RIZAL & ANDRI )

Coba ganti LCD 
Test 4 jam (hanya ON display) masih buram
cek temperatur display overheat
ganti display spare 1 set
test OK

Ganti sensor DP Separator
Test OK

Tambah Air aki

Ganti lampu 200 W 2 Ea

wbi trafo mv OTR 2, 3, 301, 302, A, B

Measure with meger at ER4 at LCS result cable bad condition. Cable to motor disconnect, run motor from CCR result motor is not available. Advise pulling cable from ER4 to LCS L93 SC4 ( YOGA & ADI & FIRMAN &  EVE RIZKY )

Replace cable power PLC ( AGUS & PENY )

Connecting new I/O for 493 AC1 ( PENY & YOGA )

Install motor at local also replace coupling motor. Adjust position coupling for all motor. Test run motor measure vibration and noise LQ1 Vertical: 0.9 mm/s o.64 gE- Horizontal: 0.0 mm/s 0.7 gE, LQ2 Vertical: 5.0 mm/s 1.9 gE Horizontal: 1.5 mm/s 1.4 gE, LQ3 Horizontal: 1.2 mm/s 0.75 gE,, Vertical: 1.0 mm/s 0.68 gE ( ADI & FIRMAN & EVE RIZKY )

Install sensor for RTD and vibration ( RIZAL & ANDRI )

Prepare box for connection cable RTD and vibration. Install box at local 9 RIZAL & ANDRI )

Install I/O for 363 RM1 ( PENY )

Replace MC incoming ( AGUS & EVE RIZKY )

Discouple motor 463 LQ1-LQ2-LQ3, clean up body motor from dust also replace bearing motor. Install motor at work shop for 463 LQ1-LQ2-LQ3( YOGA & ADI & FIRMAN )

Check condition bearing motor for 363 LQ1-LQ2 vibration normal but noise already 1 ge. 463 LQ1 - LQ3 check vibration are abnormal and noise motor are abnormal ( AGUS )

Reinstall sensor vibration, test run motor 473 EH1 from CCR, measure vibration from local and CCR. Differential 0.30 mm/s ( RIZAL & EVE RIZKY )

Relocation power for HOIST from hot material grate cooler ( FIRMAN & ANDRI )

Relocation relay panel I/O 363 RM1. Install MCB and terminal distribution 3 each. Connecting cable ( PENY & ADI )

Replace charging battery 12 VDC 2 each for number 7 & 8. Test on result ok. measure voltage good ( EMIS & ADI )

Move relay I/O 363 RM1 ( PENY & FIRMAN )

Clean up conduit from I/O panel to 473 Hc1, pulling cable vibration sensor from panel I/O to sensor vibration ( YOGA & ADI & EVE RIZKY & ANDRI & FIRMAN )

Install load cell 453 PF1 ( RIZAL & ANDRI )

Check I/O for 363 RM ( PENY )

Replace bearing motor door for north side ( OENY & FIRMAN )

Calibration protection relay ( AGUS & YOGA )

Inspection electrical and welding tools of PT KALENESIA at main gate ( ADI & IMAN )

Replace bearing for convensator 2 each. Install convensator at 453 PF1 ( RIZAL & ANDRI )

Do calibration protection relay ( AGUS & IMAN )

Check elevator found nut for inside door 1 nut is loos, install nut of inside door. Test functional from 8th to 1st floor. Result ok ( PENY & ADI & FIRMAN )

WBI Pompa line Nar 2
Regreasing motor pompa

WBI kompresor Line Nar 2
Regreasing main motor 

Cek MC 170A rusak
ganti MC 170A
perbaikan kabel output MC main (kabel Motor getas)
test OK

Perbaikan kabel power (sambungan)
test OK

Cek kabel ada yang kegaruk excavator di tiang no 4
perbaikan kabel tiang no 4

Housekeeping area elektrik workshop

Cek lampu banyak yang mati
ganti lampu TL 2 Ea
perlu tarik kabel baru, kabel netral ada yang putus

Clean up dan Cross Check motor spare cooling fan trafo OTR-B 5 Ea

WBI trafo MV OTR A, B, 2, 3, 301, 302
thermograf DS dan bushing trafo

Install Stop kontak 1 Ea
pulling kabel
connect to kabel power ke stop kontak
test OK

Install Selector Switch on-off
Pulling kabel selector switch to panel FM200
Test OK

Install selector On-Off
pulling kabel selector switch to panel FM200
test OK

Verifikasi kWHmeter ER-7B

Cek indikasi sensor DP air filter OK
Cek flexible rubber kempot
Ganti flexible rubber (Ambil dari 444-CX2)
(Info mekanik flexible rubber barang baru dan meterialny lebih tipis)

Ganti Lampu jalan 4 Ea
test OK

Ganti kabel + socket sensor pressure
Ganti Sensor DP Air Filter
Test OK

Verifikasi kWHmeter ER-7B

WBI Trafo OTR 2, 3, 301, 302, A, B

Manuver power OTR-2
Open all Outgoing
Open Bustie OTR-2
Open Bustie MSS - ER-7B
Close Incoming OTR-2
Close all outgoing

Verifikasi kWHmeter ER-7B

pasang sangkar untuk lampu tembak
pasang lampu tembak 200W
pulling kabel untuk lampu tembak 
connect kabel power
test OK

Perbaikan handpallet ganti all oil seal
test OK

Replace bright lamp that are off with new bright lamp 2 each at 363 BE1, test functional result ok ( ADI & ANDRI ) 

Install siren and lamp emergency at ER 3, test functional result ok ( AGUS & FIRMAN )

Replace bright lamp 4 each with new bright lamp at 363 BC1, test functional ok lamp are on ( ADI & ANDRI )

Replace bright lamp off with new spare ( ADI & ANDRI )

Relocation power for hoist at 473 Eh3 from hot material from under grate cooler ( AGUS & FIRMAN )

Install bright lamp at L1C BC7 3 each. Do test functional of lamp result ok all bright are on ( ADI & ANDRI )

Cross check interlock BD at L33 BC1, continue connected cable BD to interlock at systems ( RIZAL & GEMAN TRUBA )

Do replace for regulator filter ( RIZAL & GEMAN TRUBA )

Install panel I/O for 363 HS1 ( PENY & FIRMAL-MUL  CIVACON)

Test functional for 433 BF2 ( PENY )