Do repare sensor temperature 443 Z4B T1 found cable short at temperature transmitter service cable also cross check temperature compare reading local at CCR result different 5 degree celsius to 7 degree celsius. Clean up temperature IR TAD for flange probe ad lens of sensor result reading temperature normal ( RIZAL & ANDRI )

Clean up area motor and filter motor. Measure vibration-noise-temperature of FS and LS. Add grease motor 25 times and 30 times of FS and LS to make vibration below 4 mm/s and noise below 2 gE. Check at ER4 and ER5 for RPM-KW-Voltage-Ampere-Temperature and write at data check sheet ( MUHAIMIN & DADANG )

Clean up area motor and filter motor. Measure vibration-noise-temperature of FS and LS. Add grease motor 15 times and 25 times of FS and LS to make vibration below 4 mm/s and noise below 2 gE. Check at ER4 and ER3 for RPM-KW-Voltage-Ampere-Temperature and write at data check sheet note fan of south side 443 FN1 not working make notification ( AGUS & ADI )

Replace breaker and do test signal of upgrade analyzer 463 2K1 also activation signal pressure result good ( AGUS & MUHAIMIN & DADANG )

Do clean up flange probe-sample line-filter sample line-diaphragm pump-filter balston from dirty of dust coal use instrument air supply also water for filter sample line. Check humidity sensor and replace humidity result function humidity sensor good also filter humidity good condition ( RIZAL & ANDRI )

Do complete data check sheet PMR analyzer L63 2K1-L63 2k2-L63 2K3-483 2K1-463 2K1-443 2K1-423 2K1 for 1st week of October 2026; PMR critical motor area CM-CC-KL-RM-PH for 1st weeks of October 2026. Create SOT for October 2026 ( JAJAT & ADI & EDI )

Do clean up purge air unit and filter motor of dust hunter and flowsic.-swivel window T/R also R-flange with tube of T/R from dirty of dust use instrument air supply also equipment cleaning tools & R unit alignment T/r also R unit result ok-transducer probe A also transducer B from dirty of dust use instrument air supply also equipment cleaning tools-CEMS room also filter cabinet MCS 100 E-gas CEMS room from dirty of dust use equipment cleaning tools and instrument air supply ( RIZAL & ANDRI )

Do WBI sump pump electrical at room L63 HS1-IDO tank-L1C BC1-L1BC4 test function sump pump result working normal note there is no permanent way for water sump pump room L63 HS1. Do PMR service 443 EL1-clean up room of elevator also outside room every floor from 1st to 8th floor-clean up top elevator room-service sensor 1sr floor to 8th floor. Activation temperature control of 8th floor elevator control test function result ok ( AGUS & ADI & MUHAIMIN & DADANG )

Do replace breaker and test signal of upgrade IKGA result normal working ( AGUS & MUHAIMIN )

Service solenoid valve compartment 6 & compartment 7 from dirty of dust coal test function result normal working ( RIZAL & ANDRI )

Do installing lighting lamp to street cooler at HRG room back side and IDO room west side also pulling cable power of lighting lamp test function result good ( JAJAT & EDI & ADI & DADANG )

Do install plywood board for cover wall elevator control at 8th floor and repainting grey color also cover hole at elevator control mote take 2 plywood board ( JAJAT & AGUS & EDI & RIZAL & ADI & IMAN & ANDRI & DADANG & MUHAIMIN )

Do fabrication door of room control elevator at workshop ( ANDRI & DADANG )

Do clean up area motor and filter motor. Measure vibration-noise-temperature of FS and LS motor. Add grease motor for 15 times and 20 times for FS and LS motor make vibration below 4 mm/s and noise below 2 gE. Check at ER3 and ER4 for RPM-Voltage-Ampere-KW-Temperature put at data check sheet also clean up filter 363 FA2 note filter at west side 1 side bad condition ( EDI & ADI )

Do clean up area motor and filter motor. Measure vibration-noise-temperature of FS and LS motor. Add grease motor for 25 times and 30 times for FS and LS motor make vibration below 4 mm/s and noise below 2 gE. Check at ER4 and ER5 for RPM-Voltage-Ampere-KW-Temperature put at data check sheet ( AGUS & MUHAIMIN )

Clean up flange probe-probe-filter sample line-sample line tube-diaphragm pump-filter balston from dirty of dust use instrument air supply and water. Check function for humidity sensor and filter humidity result function humidity sensor good and filter humidity fine. Repare support proximity of IKGA result good ( RIZAL & ANDRI & DADANG )

Do complete data check sheet PMR analyzer L63 2K1-L63 2K2-L63 2K3-483 2K1-463 2K1-443 2K1-423 2K1; PMR Temperature  IR TAD-T scanner-CCTV-Camera burner month august-september 2026 ( JAJAT & ADI )

Do connect motor 393 SCA M1 test function motor result good  ( JAJAT & AGUS & EDI & RIZAL & MUHAIMIN & ANDRI & DADANG )

Fabrication welding point at workshop result ok ( AGUS & MUHAIMIN )

Install indication ready for trafo also pulling cable to I/O panel test function result good ( JAJAT & RIZAL & EDI & ANDRI & MUHAIMIN& DADANG )

Do inspection electrical tools of PT PINCURAN MAS tagging equipment use yellow color note service portable map and extension cable because unsafe cable power also make note for cable extension that use at indoor area because no cover of male connector ( EDI & ADI )

Fabrication door also install cover of wall and di tidy up elevator control use brush and equipment cleaning tools ( JAJAT & AGUS & RIZAL &  ANDRI & MUHAIMIN & DADANG )

Do fabrication of panel welding point at workshop result good ( AGUS & DADANG & EDI & ADI )

Do clean up flange probe-probe-sample line-filter sample line-diaphragm pump-filter balston from dirty of dust use instrument air supply also water for filter sample line. Check function of humidity sensor and filter humidity result function humidity sensor good and filter humidity good condition. Clean up lens of camera and flange probe IR TAD result value temperature show around 960 degree celcius at CCR operator ( JAJAT & RIZAL & ANDRI )

Clean area motor and filter motor from dirty of dust use instrument air supply and rag. Measure vibration-noise of FS and LS add grease motor for 25 times and 30 times of FS and LS. Check at ER4 and ER5 for RPM-KW-Ampere-V input-I total put at data check sheet ( ANDRI & DADANG )

Disconnect cable power auto grease of L63 LQ2. Also reconnect cable power after finish service replace pump  test function auto grease result ok ( EDI & ADI )

Do cross check temperature at exit gas and materials cyclone 4 result  CCR reading high than local adjust range temperature transmitter ( JAJAT & ANDRI & DADANG )

Clean area motor and filter motor from dirty of dust use instrument air supply and rag. Measure vibration-noise of FS and LS add grease motor for 20 times and 25 times of FS and LS. Check at ER3 and ER4 for RPM-KW-Ampere-V input-I total put at check sheet. Clean up filter motor 363 FA2 from dirty of dust use instrument air supply note filter motor at east side one side bad condition need replace new filter motor ( EDI & ADI )

Add seal foam of hole between cable and ER VSD also wall from rust and plat . Result hole already cover by seal foam and plat for wall ( AIMAN )

Clean up filter from dirty of dust use hand blower. Reinstall filter result alarm fan disappear. Clean up filter panel VSD 363 FN1-363 FN2-443 FN1 from dirty of dust use hand blower ( AGUS & MUHAIMIN )

Check at site, looking  location install lighting lamp. Prepare support of lighting lamp and cable power wiring existing lighting lamp . Install lighting lamp and cable power lighting lamp test function result good lighting lamp on. Do observation of installation material level at L1C BC1-L1C BC2-L1C BC3. Decided material level will install top of main hole check material coal. Prepare support of material level at work shop (JAJAT & EDI & ADI & ANDRI & DADANG )

Pulling cable power and relocation conduit from main hole to protect from positive hot gas. Also install LCS at north side from existing south side ( JAJAT & AGUS & EDI & ADI & ANDRI & ANDRI & DADANG & DAFI TRUBA )

Dismantle camera burner found front lens cracked, bring down to work shop. Continue clean up all lens and part support of lens also card from dirty of dust and oil. Replace front of lens with spare unit. Reassembling camera. Install camera burner at site test function insert and retract camera result good ( AGUS & MUHAIMIN & ANDRI )

Check at location found AUTO Drain always energized, service per membrane from dirty of dust and reinstall test function result normal. Do pulling cable of 483 RF2 from LCS to panel I/O 4C1-2RB 31 ( EDI & ADI & DADANG )

Do replace lighting lamp of 443 ph1 4.5 floor and 6th floor & L93 SC2-453 PF1-l63 BF1 of bridge also relocation lighting lamp  test function result lighting lamp on ( AGUS & MUHAIMIN & ANDRI & DADANG )

Clean CB dan Add greasing area ( AGUS & EDI & ADI & MUHAIMIN & DADANG )

Clean  Filter  and  sample line ( AGUS & RIZAL & MUHAIMIN & ANDRI & DADANG )

Do replace lighting lamp at 4th and 6th floor reason blinking. Test function lighting lamp result good (AGUS & ANDRI & MUHAIMIN & DADANG )

Clean up filter 363 FA2-area motor main drive-carbon brush room from dirty of dust use instrument air supply. Measure long all carbon brush result replace carbon brush no 2 reason bad condition ( EDI & ADI )

Do calibration tonase of zero and span result good ( RIZAL & ANDRI & DADANG )

Do tapping cable power of L63 RM1 & Do tidy up cable motor of 443 WI result ok. Tap power 380 volt of panel cooling fan 443 FN1( AGUS & MUHAIMIN & KARDI CIVACON )

Replace sensor thermocouple of 463 KL1 T1 result indication available at CCR operator ( RIZAL & ANDRI & DADANG )

Do clean up LCS motor also control speed sensor and panel I/O area raw mill - feed bin from dirty of dust use wire brush - hand blower- rag. Do eliminated sticking plat at plat from of vent fan 483 FN1 M1 result ok ( EDI & ADI )

Check at site. Dismantle cover chain motor. Test running motor no load measure noise motor result  normal. Stop motor install back cover chain motor ( EDI & ADI & KARDI CIVACON )

Check at site measure resistance R-S-T found 2 cable over load. Check at terminal motor found 1 cable untighten. Do tighten cable and recover all cable use rubber isolation and cable isolation test function 483 RF2 with different speed  result normal. Check VSD of 483 RF2 test function  motor with different speed check ampere at display VSD result around 1.71 to 1.75 ampere ( JAJAT & EDI & ADI )

Replace sensor of L63 RM1 T1 use spare unit result indication normal at CCR note welding support of sensor temperature reason bad condition ( RIZAL & ANDRI & DADANG )

Check at site found actual high noise note replace bearing motor. Dismantle motor bring to work shop continue replace bearing motor. Install motor at site test run local motor measure vibration and noise of FS and LS motor result vibration below 2 mm/s and noise motor below 1 gE. Bring spare motor to location but not install because mechanic will replace complete unit note put spare motor inside analyzer L63 2k2 ( AGUS & MUHAIMIN & KARDI CIVACON )

Do clean up panel I/O area east blending & west blending - pre heater 8th - 5th- 3rd floor from dirty of dust use rag and hand blower note clean up panel I/O 5th top side from hard dust need install cover for top panel I/O to protect from dust make panel available from long term use. Do clean up panel I/O are kiln-cooler from dirty of dust also coal use rag and hand blower ( EDI & ADI & IMAN & RISNA CIVACON )

Do support black out process result ok ( RIZAL & EDI & ADI & MUHAIMIN & ANDRI & DADANG & KARDI CIVACON & RISNA CIVACON )

Install tank air blaster of temperature TAD test function result normal high pressure air and bring dwon existing tank of air blaster to workshop ( RIZAL & ANDRI )

Check panel welding 4W3-1NH found output 220 VAC 3 units bad condition replace 3 units with spare unit and panel welding 4W3-1NC found output 220 VAC 1 unit bad condition no cover available replace use spare unit result ok normal. Also panel welding at 8th floor 443 PH1 found 1 unit output 22o VAC bad condition no cover available replace use spare unit and wiring 2 units output 220 VAC result normal ( EDI & ADI )

Clean up area motor and filter motor. Measure vibration-noise-temperature of FS and LS motor. Add grease motor for 25 times and 90 times of FS and LS motor make vibration below 4 mm/s and noise below 2 gE. Check at ER3 and ER4 for KW-voltage-ampere-temperature motor and write at check sheet note noise 363 MD1 still up2 gE even add grease 1.5 bottle grease gun. Replace auto grease motor 363 MD1 at LS side issue empty grease motor ( AGUS & ADI )

Clean up area motor and filter motor. Measure vibration-noise-temperature of FS and LS motor. Add grease motor for 25 times and 30 times of FS and LS motor make vibration below 4 mm/s and noise below 2 gE. Check at ER4 and ER5 for KW-voltage-ampere-temperature motor and write at check sheet ( MUHAIMIN & DADANG )

Do PMR service: clean up probe flange-probe-filter sample line-sample line tube-diaphragm pump-filter balston form dirty of dust use instrument air supply also water. Pulling cable new fan exchanger also wiring cable power-prepare pipe for activation fan exchanger. Do pulling cable of compressor to panel I/O inside analyzer room. Do test signal result good ( JAJAT & AGUS & RIZAL & ADI & EVE INDY & ANDRI & MUHAIMIN & DADANG )

473 SC1: check at site probe and propeller normal, also inspection wiring cable measure voltage result bad condition  from color black & white replace color chocolate & white result normal. 473 SC2 check at site found propeller detached. Ask stop motor from CCR and install propeller test function result speed failure normal when start motor from CCR ( JAJAT & RIZAL & ADI & ANDRI & EVE INDY & DADANG )

Do calibration of zero and span gas some gas MCS 100E use span gas 3rd party result good drift below 2.5% ( JAJAT & RIZAL & EVE INDY )

Install fan 483 FN1 M1, test function measure ampere result 5.1 ampere also vibration FS and LS result  around 5.2 from setting maximum 7ampere mm/s to 25 mm/s-noise around 1.3 gE note because vibration high run  with 483 FN1 M2 ( MUHAIMIN & ANDRI & DADANG )

Do calibration zero and span gas for MCS 100E together with 3rd party result good ( RIZAL & EVE INDY )

Do create reporting SOT of September 2026 for 4 reporting at SHE SIG & inspection electrical tools for GENSET 2 unit PT TUPSA tagging equipment with yellow color ( JAJAT & AGUS & ADI )

Clean up flange probe-sample line-filter sample line-diaphragm pump-filter balston from dirty of dust coal use instrument air supply also water. Check function humidity sensor and filter humidity result function humidity sensor normal and filter humidity good condition ( JAJAT & RIZAL & EVE INDY & ANDRI )

Check at location found part of cover motor broken, install cover motor use wire because nuts cover bad condition ( MUHAIMIN & ADI & DADANG )

Check at site found membrane bad condition replace big membrane 6 unit and small membrane 5 units test function bag filter result normal and do PMR service CEMS result analyzer back at good condition ( RIZAL & ANDRI )

Check at site and replace card miltronics of sensor motion setting same like existing do test function speed result good at CCR ( AGUS & MUHAIMIN & DADANG )

Do clean up flange probe and lens of IR TAD-T scanner lens-CCTV lens-Pyrometer lens from dirty of dust use rag and equipment cleaning tools ( EDI & ADI & EVE INDY )

Do replace lighting lamp at area 363 RM1 use spare lighting lamp 2 units test function result normal on ( MUHAIMIN & DADANG & ANDRI )

Pipe purging blocked, replace tube for purging test function result normal (Rizal & Andri)

Check at location found relay 24 VDC bad condition of coil, service coil replace 1 unit relay test function aeration normal note spare relay 24 VDC( RIZAL & ANDRI )

Check at location found 4 nuts untighten. Replace nuts motor with spare units note 2 nuts can not replace because part of drat nut left at flange motor ( EDI & ADI & EVE INDY )

Clean up area motor and filter motor. Measure vibration-noise of FS and LS add grease motor 25 times-30 times for FS and LS make vibration below 4 mm/s and noise below 2 gE. Check at ER4 and ER5 for KW-Voltage -Ampere-Temperature of motor fill in at check sheet motor note replace tank of AUTO grease motor 2 units ( JAJAT &MUHAIMIN )

Clean up area motor and filter motor. Measure vibration-noise of FS and LS add grease motor 25 times-30 times for FS and LS make vibration below 4 mm/s and noise below 2 gE. Check at ER4 and ER5 for KW-Voltage -Ampere-Temperature of motor fill in at check sheet motor ( AGUS & DADANG )

Clean up filter sample line and do zero also span calibration for CO result normal and reading CO back to normal at CCR ( RIZAL & EVE INDY & ANDRI )

Do WBI welding and lighting area kiln also cooler ( EDI & IMAN )

Do check at site found s/v bad condition, replace 4 s/v test function result working normal ( RIZAL & MUHAIMIN & EVE INDY & DADANG )

Do make list of motor down at OH 2027 included bearing  ( AGUS & JAJAT )

Clean up flange probe-sample line tube-sample filter-diaphragm pump-filter balston from dirty of dust coal use instrument air supply and equipment cleaning tools. Test function humidity sensor and check filter humidity result function sensor humidity normal and filter good condition ( RIZAL & ANDRI )

Check at location found receptacle trip at panel lighting lamp. Do elimination 2 receptacle at north side and south side do rewiring cable for lighting lamp test function result normal ( EDI & ADI & EVE INDY & DADANG )

Check at ER4 and do reset power of KW metering result indication KW normal at CCR ( AGUS & EDI & DADANG )

Check at location found belt roller crooked make good position of belt roller and install speed monitor result indication normal at CCR operator ( JAJAT & RIZAL & ANDRI & EVE INDY & UNJ AZRIEL )

Clean flange probe-probe-sample line filter-sample line line tube-diaphragm pump-filter balston from dirty of dust use instrument air supply. Test function humidity sensor and check filter humidity result function humidity sensor normal and filter humidity good condition note replace filter humidity at 443 2K1 with spare filter. Do test gas CO at 463 2K1 reason reading often -0.001 to 0.002 result reading CO 1.1 PPM ( RIZAL & ADI & EVE INDY & ANDRI & UNJ AZRIEL )

Do test function BD of L1C BC2 result normal  ( EDI & EVE INDY & ANDRI )

Clean up area motor and filter motor. Measure vibration-noise of FS and LS. Check ampere-KW-voltage-temperature at ER4 & ER5 put in check sheet form ( AGUS & DADANG )

Do support TPM activity ( RIZAL & AZRIEL UNJ & EVE INDY )

Do fabrication piping of water and air for support  AC Rubicon ER4 (EDI & DADANG & ANDRI )

Replace Tesys LUB12 also jumper contact relay test function fan cooling motor working normal and check vibration motor result still good ( AGUS & ADI & ANDRI )

Do clean up carbon brush room of 363 MD1-363 FN1-363 FN1 from dirty of dust use instrument air supply also clean up filter 363 FA2. Measure long of all carbon brush result still up to minimum ( EDI & DADANG )

Do repare of ER4 use welding machine ( ADI & ANDRI )

Do calibration zero and span result zero before 0 t/h zero after 0 t/h- span before 155 t/h span after 161 t/h-Replace speed sensor, result indication normal at CCR-Do install lighting lamp test function result  lighting lamp on ( JAJAT & RIZAL & UNJ AZRIEL & ANDRI )

Open cover cable heater motor, rewiring cable heater 363 FN1-363 FN2-463 MD1. Tidy up recondition motor put at north side and spare motor at south side ( AGUS & ADI & DADANG )

Clean up flange probe-sample line tube-filter sample line-diaphragm pump-filter balston from dirty of coal dust use instrument air supply. Check function humidity sensor and filter humidity result function humidity sensor normal and filter humidity good condition ( RIZAL & ANDRI )

Check value pressure at 444 PI 13A at 7th floor use manual manometer show pressure 131 to 150 mmH2O compare with CCR reading 660 mmH2O check range existing -4 to 0 mmH2Ot change range to 0-600 mmH2O result reading local same with CCR. Check reading temperature 444 PH1 T3 reading minus at CCR check connection cable and do recorrect wiring cable result temperature good. 444 GT4 materials don't flow to sirculation try change open and close gate result still same and use instrument air supply to make materials go to sirculation point result good ( JAJAT & EDI & ADI & MUSLIH SHIFT & RIZKY SHIFT & RIZKY FAUZI & SUPRIYADI & DADANG & IMAN )

Do support YM CEMS with Mr. Hannes and Mr. .Adrianus. Clean up Flowsic 100 complete unit also filter purge air unit. Bring down Dust Hunter T100 check zero adjust result value zero without materials 1.2 mg/m3 recheck function of swivel windows result replace swivel windows with spare units install back Dust Hunter at stack result value dust 4 until 5 mg/m3 ( RIZAL & ANDRI & HANNES KISS & ADRIANUS KISS )

Do clean up area HRG inside and outside also filter panel  from dirty of dust use instrument air supply ( JAJAT & UNJ AZRIEL )

Clean up flange probe-probe-filter sample line-sample line tube-diaphragm pump-filter balston from dirty of dust use instrument air supply. Check function of humidity sensor and filter humidity result function humidity sensor normal and filter humidity good condition ( RIZAL & ANDRI  )

Cleaning area and filter motor from dirty of dust use instrument air supply and equipment cleaning tools. Measure vibration-noise of FS and LS motor also add grease motor for 25 times and 30 times of FS and LS. Check at ER4 and ER5 for ampere motor-voltage motor-RPM-KW write at check sheet motor ( MUHAIMIN & DADANG )

Cleaning area and filter motor from dirty of dust use instrument air supply and equipment cleaning tools. Measure vibration-noise of FS and LS motor also add grease motor for 25 times and 40 times of FS and LS. Check at ER3 and ER4 for ampere motor-voltage motor-RPM-KW write at check sheet motor ( EDI & ADI )

Do install sling cable of TLS at south and north side also support of sling cable. Do test function TLS result good ( IRMIS & ADI & MUHAIMIN & ANDRI & DADANG )

Do installation sensor temperature and humidity at room hydraulic Nr2 also wiring cable at I/O panel ( AGUS & MUHAIMIN & DADANG )

Achieve motor 463 MD1 from BOVERI put motor behind workshop ( AGUS & MUHAIMIN & DADANG )

Do inspection electrical tools of PT INDOPORLEN for jack hammer 4 units test run tools result ok note equipment tagging blue color ( EDI & ADI )

Prepare cable for signal indication output ampere motor of VSD L64 SC1 continue wiring cable at I/O panel ER5 Nr2 ( ZAHRA & ADI )

Check name plate motor of 443 WI1 M1 and 443 WI1 M3 and cross check spare motor at warehouse result find motor 2P 45 KW do test run megger motor result good no load measure ampere R-S-T get value 10 until 12 ampere and put motor spare 443 WI M3 behind workshop electric 1 ( EDI & ADI & JAJAT )

Check local, Replace Probe test blm bisa pulse, Replace Amplifier test bisa pulse. Test Run L94-SC2 Sudah tidak mati Ready lagi/ normal
( Melky, Yulandi, Kardi )

Check local, Replace Probe test masih blm pulse, Ganti Amplifier test langsung dengan motor L94-SC2 Kondisi bisa pulse/ok

Replace probe and pre amplifier at local test function result normal ( TITOK & FAHRI & EVE TEGAR & EVE ZAHRA & KARDI CIVACON & ADI )

Install support and sensor motion at 394 CV2-CV3-CV4-CV5 ( EVE SUPRIYADI & KARDI CIVACON & ADI )

Install motor at 454 PF2 and bearing motor 434 BL2 at workshop electric Nr2 with do heater bearing 6213 before install  at motor ( HARYANTO & EDI & ADI )

Create SOT document for month august for all member at electric RMK Nr1 ( JAJAT & ADI )

Clean up area panel cable motor-connector cable-winding cable from dirty of dust use hand blower and liquid dust degreaser also clean up area motor from dirty of dust. Test run without load result good ( HARYANTO & ADI & @ CIVACON EMPLOYEE )

Replace OCR, ganti dgn EOCR+ instal CT... Test trip Done

Replace OCR, ganti dengan EOCR + instal CT..test trip..Done 

Do clean up panel VSD of 364 FN2 & FN3 also filter cabinet-bus bar-cable power supply from dirty of dust use hand blower and thinner also equipment cleaning tools ( ADI & EVE ELGI & KARDI CIVACON & RAHMAT CIVACON  & EKO & MARDIYANTO )

Replace OCR + Replace R1

Replace EOCR dan test trip ok

Do clean bus bar-capacitor inverter-filter panel use hand blower and thinner. Measure value of capacitor write top of capacitor. Reinstall filter panel of VSD ( EKO JUAN & MARDIYANTO & ADI & EVE ELGI & KARDI CIVACON & 2 CIVACON EMPLOYEE )

Replace motor & EOCR

Instal level material,trashing kabel

Do inspection electrical tools of PT RMP for panel power supply AC tagging equipment use blue color ( ADI & EVE ELGI )

Replace TOR dengan EOCR

Replace EOCR, seting ampere sesuai dgn existing dan test manual trip ok.. Done

Do  calibration pressure transmitter area PH 5 units note replace pressure transmitter of 444 FN2 P2 from VEGA to Yokogawa because when give pressure at H or L always drop to zero  do test zero and span result normal. Complete data check sheet calibration pressure transmitter for 12/8/2026 ( ADI & EVE ELGI & EVE INDY & EVE TEGAR )

Check cable power input 110V...cable netral 110V Conectionnya kendor.

Replace selector switch

Check power control purging ada yg shot

Check yg noist bearing motor yang LS dengan cara di discouple, hasilnya tidak ada noist.
CBM Alignment ulang motor 546-RM1.M1

Test trip EOCR dan List data set EOCR all equipment

Replace TOR dengan EOCR+CT ratio 400/5

Do calibration pressure transmitter Honeywell 3 units but can not detected name of unit base on instruction Mr.Titok install back pressure transmitter at site no need replace new spare. Complete data check sheet calibration pressure transmitter since 4/8/26 to 10/8/26 ( ADI & EVE TEGAR & EVE INDY & EVE ELGI & UNJ AZRIEL )

Ganti tor ke eocr

Ganti tor dengan eocr

Cek seting EOCR all equipment and test trip EOCR

Replace relay R1 dgn yg baru, test.. Ok

Replace TOR dengan EOCR... Test position trip dan seting trip sesuai sebelumnya 

Calibration pressure transmitter area PH-CC-RM for zero and span get 20 units note replace pressure transmitter from VEGA of 364 BF1 F1 use Yokogawa test zero and span result good ( ADI & EVE TEGAR & UNJ AZRIEL & EVE ELGI & EVE INDY )

Check,service dan setting damper fan R

Replace thermocouple exit cooler,inlet ep cooler

Replace valve kinetrol untuk flushing gun

Suport black out activitg,clean up switch gear and mcc,meger buabar dan trafo

Lepas thermocouple undergrate

Repair tubing yg rusak,rojok lubang draft flow fan cooler area

Tap power untuk control drive portable alat gulung belt dan pulling cable output drive ke motor serta test running.

Instal dan connect motor setelah rekondisi dari vendor Rems.

Jumper outgoing kubikel W1E ke kubikel EP cable 6 x 240 mm.

Ganti cable dan pasang grounding motor.

Ganti baut base motor 484 BL2 dan modifikasi base.

Penggantian proteksi dari TOR ke EOCR

Penggantian dari Proteksi TOR ke EOCR

Service VCB & Blow out

Do calibration zero and span for pressure transmitter area raw mill-cooler-preheater-coal mill totals 6 units ( EVE TEGAR & ADI )

Blow out trafo & penegecekan baut conection

Perbaikan penggantian kabel battery yang short.
Service dan cleanup periodik.

Do inspection electrical and welding tools of Quadro. Tagging electrical tools use blue color note extention cable 2 units no cover female connection ask quadro replace with cover for all female connection (  ADI & TRUBA ILHAM )

Clean up area motor and filter motor. Measure vibration-noise-temperature of FS and LS motor. Add grease motor for LS and FS 25 times and 30  times . Check at ER5 and ER4 for data KW-Ampere-Voltage-Temperature and fill in at data check sheet ( AGUS & MUHAIMIN )

Clean up area motor and filter motor. Measure vibration-noise-temperature of FS and LS motor. Add grease motor for LS and FS 15 times and 20  times note 363 MD1-363 FN1-363 FN2 off condition. Check at ER3 and ER4 for data KW-Ampere-Voltage-Temperature and fill in at data check sheet ( EDI & DADANG )

Clean up flange probe-probe-filter sample line-sample line tube-diaphragm pump-filter balston from dirty of dust use instrument air supply. Check function humidity sensor and filter humidity result function humidity sensor normal and filter good condition ( RIZAL & ANDRI )

Do support black out process at ER2-ER5-ER4-ER3. Clean up trafo-MCC-MSS -I/O panel from dirty of dust use equipment cleaning and hand blower also do vacuum electric room. Do megger cable R-S-T to ground fill in at check sheet of data ER2 ( JAJAT & AGUS & RIZAL & ADI & ANDRI & AIMAN & DADANG )

Penggantian Cooling Fan 3 EA, Penggantian Battery 18 EA 12V 120Ah, Service 

Penggantian proteksi TOR ke EOCR

Do calibration zero and span for pressure transmitter area raw mill-cooler-preheater-coal mill totals 10 units note replace 1 unit  pressure transmitter 364 BF1 P1 range 0-150 mmH2O calibration result good because existing pressure transmitter check span output drop to 7 mA ( ADI & EVE TEGAR & UNJ AZRIEL )

Penggantian proteksi dari TOR ke EOCR

Penggantian dari TOR ke EOCR

Support OH Nar2 disconncet dan bongkar motor 364-LQ1,394-FA6,434-FA1,L94-SC3,L94-SC6,L94-FN2 untuk rekondisi keluar ke PT Rems dan Tridaya.

Support OH Nar 2 Disconnect dan bongkar motor L94 RF1,RF2, 484 FN4 rekondisi motor ke luar PT Rems dan Tridaya.

Do calibration zero and span for pressure transmitter area raw mill-cooler-preheater-coal mill totals 10 units ( ADI & EVE TEGAR & UNJ AZRIEL )

Check,service repair ganti card,repaire blade dan setting

Check open close damper dari ccr

Check open close damper

penggantian Cooling Fan sebanyak 3 EA dan service tahunan

Service tahunan, ganti fan 3EA

Blow out & ganti lampu tl yg mati di dalam panel I/O

Hasil pengukuran capasitor :
( Y1+PH )               ( Y2+PH )               ( Y1+Y2 )
  42,87uF                  42,94uF                 21,47uF
  42,42uF                  39,68uF                 20,51uF
  42,90uF                  39,50uF                 20,60uF

Pengecekan respon trip dari EOCR

penggantian proteksi menjadi EOCR 

Do calibration zero and span for pressure transmitter area raw mill-cooler-preheater totals 15 units ( ADI & EVE TEGAR & UNJ AZRIEL )

Disconnect dan lepas motor 484 BL2,454 BL4 untuk rekondisi keluar ke PT Rems.

Disconnect dan lepas motor 474 CV1,CV2,CV3,CV4 untuk rekondisi keluar ke PT Tridaya.

Blow out panel tubical 380V dan vacum lantai mcc ER04A

Pengecekan respon proteksi EOCR serta pengecekan equipment yang masih menggunakan TOR sebagai berikut:
474-GD1.M2
Set : 5A

434-BL7
Set : 60 A

444-PU1.M2
Set : 115 A

474-GD1.M01
Set :3.5

414-BL5 
Set : 20A

4D4-BL1.M01
Set : 275 A

454-WS1.C1
Set : 60 A

Replace lampu indikasi yg baru

Lepas pressure transmitter area great cooler

Lepas pressure transmitter fan cooler all

Do calibration zero and span for pressure transmitter area raw mill 4 units ( ADI & EVE TEGAR & UNJ AZRIEL )

Repair diafragm bocor,replace solenoid rusak,clean up panel purging

Survey oleh Trafindo persiapan service, ganti oli, bushing dan seal termasuk purifying.

rencana penggantian batere tipe basah dengan batere tipe kering bersamaan service OHN2-2026 bulan Agustus.

Do adjusted CF ( RIZAL & ANDRI )

Do inspection electrical and welding tools of PT Adzalama tagging equipment bule color note repare brook machine because grounded cable not connected properly. Rejected 2 extention cable because no cover at male connector ( ADI & WILDAN CIVA & MUSLIH SMI )

Do  complete data AUDIT API ( JAJAT & ADI & UNJ AZRIEL )

Dust hunter: clean up purge air unit-filter motor flange with tube-swivel window T/R & R -alignment T/R  & R result ok. Flowsic: clean up purge air unit-filter motor-transduce A & B. CEMS room: clean area CEMS room-filter cabinet MCS 100E-CEMS gas room from dirty of dust use instrument air supply ( RIZAL & ANDRI )

Do continue project upgrade 463 2K1 and test signal result ok ( AGUS & DADANG )

Do WBI area CM-truck lift-tripper-bc transport coal. Add grease for L1C BC4-L1C BC5-483 BL2 around 15 times-20 times-30 times for FS and LS. Test function sump pump L1C BC1 & L1C BC4 result normal-water spray  L1C BC5 & L1C BC6 & L1C BC7 & L63 HS1 result function normal ( EDI & ADI & UNJ AZRIEL )

Install motor blower shell kiln 4 units- install cable motor blower shell kiln; install propeller motor blower. Do test function blower shell kiln result function normal. Bring down 1 motor shell kiln to workshop for rewinding ( JAJAT & AGUS & RIZAL & ADI & EDI & MUHAIMIN & ANDRI & DADANG & TRUBA TEAM & UNJ AZRIEL ) 

 Clean up flange probe-probe-sample line tube-filter sample line-diaphragm pump-filter balston from dirty of dust coal use instrument air supply and water supply. Check function humidity sensor and filter humidity result function humidity sensor normal and filter good condition note replace gas cooler at L63 2K3 because bad condition replace use spare unit ( RIZAL & ANDRI )

 Clean up motor area clinker silo from dirty of dust clinker use equipment cleaning tools. Measure vibration-noise and add grease motor 25 times for FS and LS ( DADANG & AIMAN )

Continue  activity wiring LCS and IO ( AGUS & MUHAIMIN )

Check inspection electrical and welding tools of PPUP. Do repare some tools and tagging equipment use blue color ( EDI & UNJ AZRIEL )

Adjust CF , reduce around  - 4 t/h ( RIZAL & JAJAT )

Pulling cable   4 x 10 mm x 120 m -Done ( AGUS & RIZAL & MUHAIMIN & DADANG )

Clean up flange probe-probe-sample filter-sample line tube-diaphragm pump-filter balston from dirty of dust use instrument air supply. Check function humidity sensor and filter humidity result function humidity sensor good and filter humidity good ( RIZAL & ANDRI )

Clean up area motor-filter motor from dirty of dust use instrument air supply. Measure vibration-noise motor of FS and LS add grease motor 25 times for FS and LS. Check at ER4 and ER5 for RPM-Voltage-KW-Ampere-Temperature fill in at check sheet motor note replace AUTO grease tank at L63 MD1-L63 FN1 for FS and LS with spare unit ( MUHAIMIN & DADANG )

Clean up area motor-filter motor from dirty of dust use instrument air supply. Measure vibration-noise motor of FS and LS add grease motor 15 times for FS and LS. Check at ER3 and ER4 for RPM-Voltage-KW-Ampere-Temperature fill in at check sheet motor ( EDI & ADI & UNJ AZRIEL )

Do TPM activity at ER5 bottom floor. Clean up room ER5 from dirty of dust use equipment cleaning tools ( JAJAT & AGUS & EDI & RIZAL & ADI & MUHAIMIN & ANDRI &  AIMAN & DADANG & UNJ AZRIEL )

Check at location, L1C BC7: found power s/v off and valve water spray off. Do turn on power s/v and valve water spray  also adjust stick water spray result function water spray normal, L1C BC6 found valve water spray off action valve water off action on valve water and adjust stick water spray result function water spray normal. L1C BC5  found valve water spray off action open valve water spray function water spray normal ( EDI & ADI & DADANG )

Check use megger of R-S-T to ground result 0.4 ohm note inside motor moist hit water from 443 WI1 M2. Install heater lamp at motor 443 WI1 M3 around 10 minutes reconnect cable R-S-T and do megger result 2 mega ohm. Test function motor 443 WI1 M3 result ampere meter 13-14 ( JAJAT & EDI & ADI & UNJ AZRIEL & DADANG )

Check noise motor 363 MD1 of FS and LS  result LS around 2,4 gE add grease motor 15 times-FS noise  9.85 gE; 363FN1 noise LS and FS around 1.5 gE add grease motor 15 times; 363 FN2 noise motor LS 2,4 gE add grease motor  15 times-FS noise around 2.3 gE add grease motor 15 times ( CBM NAJIB & ADI & UNJ AZRIEL )

Clean up flange probe-sample line tube-filter sample line-diaphragm pump-filter baslton from dirty of coal use instrument air supply and equipment cleaning tools. Check function humidity sensor and filter humidity result function humidity sensor normal and filter humidity good  ( RIZAL & ANDRI )

Replace 3 unit AUTO grease tank because existing low level with spare unit ( EDI & ADI )

PMR service analyzer such as clean up flange probe-sample line tube-filter sample line-diaphragm pump-filter balston from dirty of dust use equipment cleaning tools and instrument air supply. Check function humidity sensor and filter humidity result function humidity sensor normal and filter humidity good ( RIZAL & ANDRI )

Do support team safety and student university at job training for inspection electrical and welding tools ( EDI & ADI & SAFETY JOKO & STUDENT  UNIVERSITY JOB TRAINING )

Check actual noise  with CBM Mr. Najib at 363 FN2-363 FN1 of FS & LS result noise FN2 FS 2.42 gE-LS 1.81 gE-FN1 noise FS 0.85 gE-LS 0.94 gE add grease for FS 15 times of FS and LS at FN2-add grease 15 times for FS and LS at FN1; 363 MD1 check noise motor at  FS result 0.35 gE LS 2.4 gE add grease 15 times; check noise motor at L63 MD1 FS and LS add grease motor 20 times at LS and 15 times at FS; add grease motor 10 times at 483 BL5 for FS and LS; add grease motor 10 times for FS and LS at 483 BL9 ( EDI & ADI & NAJIB CBM )

Do WBI Elect & Ins & Check I/O CM, Sump T&T. Test function sump pump and clean up motor sump pump result function good and area motor clean note at area sump pump L1C BC4  dirty of coal need clean up ( EDI & ADI )

Clean up purge air unit motor and filter motor from dust use instrument air supply. Dust hunter: clean up flange with tube-swivel window T/R-R unit-alignment result normal function. Flowsic 100: clean up transducer A & B also flange from dirty of dust use equipment cleaning tools and instrument air supply. CEMS room: clean up CEMS room analyzer-filter cabinet 0f MCS 100E-CEMS gas room from dirty of dust use equipment cleaning tools and instrument air supply ( RIZAL & UNJ AZRIEL & ANDRI )

Check actual noise with CBM team Mr. Najib found 363 FN2 for LS and FS below 2 gE but 363 FN1 for FS noise 2.5 gE add grease 15 times measure noise result 0.85 gE and for LS noise below 1 gE. Check noise at 363 MD1 for FS below 1 gE but LS 2.4 gE add grease 15 times measure noise 1.5 gE Check at location found support vibrator broken at round bar. Repare round bar by mechanic team result function vibrator normal ( EDI & ADI & DADANG & CBM NAJIB )
. 

Do continue project upgrade 463 2K1 and install 3 LCS with canopy ( AGUS & MUHAIMIN )

Do continue project upgrade 463 2K1. Replace and install lighting lamp at 443 FN1 also hydraulic room test function lighting lamp result lighting lamp normal on ( RIZAL & UNJ AZRIEL & ANDRI & DADANG )

Clean up area motor and filter motor. Measure vibration-noise of FS and LS, add grease motor 25 times- 30 times for FS and LS make vibration below 4 mm/s and noise below 2 gE. Check at ER5 and ER4 for RPM-KW-Voltage-Ampere-Temperature and fill in at check sheet ( MUHAIMIN & AGUS )

Clean up area motor and filter motor. Measure vibration-noise of FS and LS, add grease motor 15 times for FS and LS make vibration below 4 mm/s and noise below 2 gE. Check at ER3 and ER4 for RPM-KW-Voltage-Ampere-Temperature and fill in at check sheet ( EDI & ADI )

 Replace module and check power 24 VDC result normal indication at panel I/O also CCR ( JAJAT & MUAIMIN )

 Check limit switch and repare incline plat of 433 BE1 result normal indication.  Check limit switch and cylinder also indication open-close at CCR result in accordance ( AGUS & MUHAIMIN )

Clean up carbon brush room from dirty of dust use instrument air supply. Check and replace carbon brush area 463 MD1 and 473  FN7 result 1 CB area 463 MD1 with spare unit because bad condition ( EDI & DADANG )

Do calibration dynamic zero and span for 453 PF1 result good ( RIZAL & UNJ AZRIEL & ANDRI )

Clean up panel I/O of  413 3B1-413 3B1-panel  power supply-panel solenoid valve from dirty of dust use hand blower also equipment cleaning tools ( ADI & JAJAT )

Clean up area motor purge air unit and filter purge air unit-flange with tube of Dust Hunter-swivel window of Dust Hunter-alignment Dust Hunter result good-transducer A & B of Flowsic 100-CEMS room-CEMS gas room-filter cabinet MCS 100 E from dirty of dust use instrument air supply and equipment cleaning tools ( RIZAL & ANDRI )

Clean up are cable drum and adjustment sensor result ok ( AGUS & MUHAIMIN & DADANG )

Replace 1 lighting lamp test function result good ( MUHAIMIN & DADANG )

Do inspection electrical  and welding tools of plant building, tagging equipment blue color note repare some extention cable and portable lamp because cable ground not connected ( EDI & ADI & UNJ AZIEL )

Replace 2 unit lighting lamp at L63 BF1 test function result lighting lamp on ( AGUS & MUHAIMIN & ANDRI & DADANG )

 Data line broken because trouble at switch gear solved ( JAJAT & AGUS )

Replace membrane solenoid valve of water test function result  gun no 19 of water no leakage ( MUHAIMIN & ANDRI )

Clean area motor and filter motor also clean filter motor of 363 FA2 from dirty of dust use instrument air supply. Measure vibration-noise-temperature of FS and LS add grease motor 20 times and 25 times of FS and LS. Check KW-Ampere-Voltage-Temperature motor at ER3 and ER4 also fill in at check sheet ( AGUS & DADANG )

Check function cooling fan of area WF and AC result normal function. Clean up area room VSD area WF and AC note equipment tools are not available need make available make easy to clean up area vSD WF and AC ( ADI & AIMAN )

Do replace sensor vibration and tighten sensor vibration result reading vibration 1.2 mm/s ( MUHAIMIN & UNJ AZRIEL & DADANG )

Pulling cable profibus from IKGA to station 22 ( MUHAIMIN & ANDRI & DADANG & ADI )

Clean up area motor and filter motor. Measure vibration-noise-temperature of  FS and LS motor also add grease motor 25 times and 30 times. Check at ER4 and ER5 for RPM-Voltage-Ampere-KW-Temperature of motor and fill in at check sheet ( MUHAIMIN & UNJ AZRIEL & DADANG )

Clean up flange probe-probe-sample filter-tube sample line-diaphragm pump-filer balston from dirty of dust use equipment cleaning tools. Check function humidity sensor and filter humidity result function humidity sensor normal and filter good condition ( ADI & ANDRI )

Do fabrication structure control and station 423 2K1 result ok ( AGUS & MUHAIMIN & UNJ AZRIEL )

Clean up flange probe-filter sample line-sample line-diaphragm pump-filter balston from dirty of dust coal. Check function humidity sensor and filter humidity result function humidity sensor normal and filter good condition ( RIZAL & EVE INDY &ANDRI )

nstall motor and rectifier test function result normal ampere motor 2.3 DC to 2.5 DC ( EDI & ADI & EVE ABY & EVE ELGI & DADANG )

Testing  Wiring by life line + Install Fan  Blower ( AGUS & MUHAIMIN )

Do inspection thermograph electric room 3-4-5-6 ( EDI & DADANG )

Clean up filter purge air unit-swivel window T/R and R of dust hunter-Flange with tube from dirty dust: clean up transducer A and B flowsic 100 from dirty dust. Clean up CEMS room-filter cabinet MCS 100E-CEMS gas room from dirty of dust use instrument air supply (RIZAL & ANDRI )

Do inspection electrical tools of PT Pincuran Mas. Tagging equipment with blue color. Repairing the cable ground of portable lamp 2 units, note : 1 extention cable not safe because 2 cover missing ( ADI & EVE ABY & EVE INDY )

Re installation and wiring also testing  result ok. Prepare of new station 60% ( AGUS & MUHAIMIN )

Do clean up flange probe-probe-filter sample line-sample line-diaphragm pump-filter balston from dirty of dust use instrument air supply. Check function humidity sensor and filter humidity result function humidity sensor good and filter humidity normal also dry ( RIZAL & EVE ABY & EVE INDY & CIVACON EMPLOYEE )

Do clean up flange probe also lens Temperature IR TAD result  temperature 920 degree celcius-clean up lens of T scanner found before dirty of dust-clean up CCTV such as lens also camera unit form dirty of dust use equipment cleaning tools-clean up camera burner such as probe of camera, panel instrument air, panel control PLC, dryer oil and water from dirty of dust use hand blower and equipment cleaning tools note lens of t scanner east side cracked advice need to replace with spare unit ( ADI & EVE ELGI )

Check at site do test gas of O2 result normal .Do monitoring O2 reading ( RIZAL & EVE INDY & ANDRI )

Replace Proportional Valve, test Normal ( RIZAL & EVE ABY & EVE INDY & ANDRI )

Complete data check sheet PMR analyzer L63 2K1-L63 2K2-L63 2K3-483 2K1-463 2K1-443 2K1-423 2K1; PMR Hoist-Crane-PMR IR TAD-T Scanner-CCTV-Camera Burner-WBI electrical & instrumentation bottom blending_kiln_cooler_clinker silo-WBI electrical & instrumentation top blending_CT_PH_klin for month March to June 2026. Make SOT for month of July  2026 ( JAJAT & ADI & EVE ELGI )

Do inspection electrical tools of PT Pincuran Mas. Tagging tools use blue color note 1 extention cable not safe because not full fill safety requirement SBI ( JAJAT &  ADI )

Check voltage at transformer result value below. Replace transformer and do megger test result good. Install new transformer and do monitoring ( EDI & EVE ELGI & DADANG )

Do calibration zero and span for 423 PDT 2001 and 423 PDT 2002  with range pressure transmitter 0-20 mbar result drift good. Install pressure transmitter at site and check reading pressure result normal indication ( RIZAL & ADI & EVE ELGI & EVE INDY & ANDRI )

Clean up area motor and filter motor from dirty of dust use instrument air Measure vibration-noise-temperature of FS and LS add grease motor for FS and LS 30 times and 25 times make vibration below 4 mm/s and noise below 2 gE. Check at ER5 and ER4 for data RPM-Voltage-Ampere-KW-Temperature motor and fill in at check sheet ( MUHAIMIN & DADANG )

Clean up area motor and filter motor from dirty of dust use instrument air Measure vibration-noise-temperature of FS and LS add grease motor for FS and LS 20 times and 25 times make vibrationbelow 4 mm/s and noise below 2 gE. Check at ER3 and ER4 for data RPM-Voltage-Ampere-KW-Temperature motor and fill in at check sheet. Also cleanup 363 FA2 of filter motor from dirty of dust use instrument air supply   ( EDI )

Do calibration zero and span for 423 PDT 2001 and 423 PDT 2002  with range pressure transmitter 0-20 mbar result drift good. Install pressure transmitter at site and check reading pressure result normal indication ( RIZAL & ADI & EVE INDY & EVE ELGI & ANDRI )

Clean up flange probe-sample line- filter sample line - diaphragm pump - filter balston from dirty of coal. Check function humidity sensor and filter humidity result function humidity sensor good and filter humidity normal condition ( EDI & DADANG )

Do make addressing-unit-range of pressure transmitter. Calibration zero and span result good. Install pressure transmitter at site and cross check reading pressure at CCR result normal reading ( RIZAL & ADI & ANDRI & EVE ABY & EVE ELGI & AZRIEL UNJ )

Add greasing motor for LS and FS for L63 MD1-483 BL5-483 BL9. Measure vibration-noise make below 4 mm/s and below 2 gE. Do check motor condition for 443 WP1 & 443 WP2 also test run ( EDI & DADANG )

Do inspection electrical and welding tools of PT Truba Jaga Cita at 8th 443 Ph1 and 463 KL1 bottom floor tagging tools use blue color ( ADI & EVE ABY & EVE ELGI )

Released Old Box + Install -reconnection   New Box Released old box and install new box also do reconnection ( JAJAT & EDI & DADANG & AIMAN )

Install + Calibration ---Done, result function FIDOR normal  Replace load cell - monitor note WF not calibration issue  material full( RIZAL & ANDRI & EVE ABY & EVE ELGI )

Do inspection electrical and welding tools of PT Truba Jaga Cita, note repare connection extention cable 2 units. Tagging tools with bule color ( ADI & EVE ELGI )

Clean up flange probe-probe-filter sample-sample line-diaphragm pump-filter balston from dirty of dust use instrument air supply. Check function humidity sensor and filter humidity result function humidity sensor normal and filter good condition ( RIZAL & EVE ABY & EVE ELGI & ANDRI )

Do pulling cable from new panel I/O to 463 2K1 room of 6 cable and put at cable tray ( JAJAT & EDI & ADI & DADANG & 2 CIVACON )

Check at site O2 reading high.. do calibration zero and span O2 run MCS100E reading O2 still high. Try disconnect FIDOR and also run MCS 100E reading O2 7-8%. Suspected s/v for zero gas FIDOR bad condition or dirty service s/v of zero gas FIDOR and install at site. Run MCS 100E result O2 reading still high. Not connected sample line FIDOR reading O2 7% note instrument air must be oil and water free suspected filter instrument air replace with spare unit ( RIZAL & EVE ABY & ANDRI )

Clean up area motor and filter motor. Measure vibration-noise-temperature FS and LS motor continue add grease motor 20 times and 15 times for FS and LS make vibration below 4 mm/s-noise below 2 gE also 363 FA2 at 363 MD1 filter motor. Check at ER3 and ER4 for RPM-Voltage-Ampere-Temperature motor and fill in at check sheet form ( EDI & ADI )

Clean up area motor and filter motor. Measure vibration-noise-temperature FS and LS motor continue add grease motor 25 times and 30 times for FS and LS make vibration below  4 mm/s-noise below 2 gE. Check at ER4 and ER5 for RPM-Voltage-Ampere-Temperature motor and fill in at check sheet form ( MUHAIMIN & DADANG )

Do make notification for job WBI Elect & Inst  Feed bin-RM-CT-Dust Transport-BF ( ADI & EVE ELGI )

Replace -Test Blower  ( AGUS & MUHAIMIN & DADANG )

Clean up flange probe-sample line-filter sample line-diaphragm pump-filter balston from dirty of coal use instrument air supply and equipment cleaning tools. Check function humidity sensor and filter humidity result function humidity sensor good and filter humidity normal ( RIZAL & EVE ABY & ANDRI )

Do WBI Elec & Ins & Check I/O & S Pump Bl,-C  (Area Kiln ). Test sump pump L1C BC4 note area very dirty of coal dust need clean-L1C BC1 note area sump pump much dirty of coal need clean up-IDO bin-L63 HS1 result good function. Clean up I/O panel area clinker silo at bottom floor-area cooler-area kiln from dirty of dust use equipment cleaning tools (EDI & ADI )

Replace transducer ampere at 363 BE1, do test function result ok ( EDI & MUHAIMIN & DADANG )

Prepare upgrade 463 2K1 and redrawing at computer  ( AGUS & MUHAIMIN & DADANG & EDI )

Do calibration zero and span for O2 result drift below 1% good ( RIZAL & EVE ABY & EVE ELGI & ANDRI )

Do make report of TPM for AM month June 2026 and safety finding 3 file continue print out and install at dash board TPM work shop ( RIZAL & ADI )

Do redrawing upgrade 463 2K1 ( JAJAT & AGUS )

Install power point at L3C RE1 continue painting support and canopy with grey color ( EDI & ADI & EVE ELGI )

Do cleaning sample line tube and filter sample line from dirty of dust use instrument air supply and equipment cleaning tools. Check at site found power common contact lose for 110 VAC  take power 110 VAC from 443 2K2 note  contact relay for purging result function purging normal ( MUHAIMIN & ANDRI & EVE ABY )

Add grease motor of FS and LS measure vibration-noise for FS and LS result vibration below 4 mm/s and noise below 2 gE ( JAJAT & EDI )

Check at site and do replace address for RUN result ok ( AGUS & JAJAT & MUHAIMIN )

Do fabrication of travelling probe continue install at site test function probe retract-inset result good ( RIZAL & DADANG )

Cross check indication temperature compare with CCR reading different do adjustment range at local make same with local value ( RIZAL & DADANG )

Do tighten nut of 413 BE1 result ok ( RIZAL & MUHAIMIN )

 Tightening terminal-fabrication blower of cooling motor and install at site ( RIZAL & MUHAIMIN )

Cleaning area motor and filter motor. Measure vibration-noise-temperature of FS and LS motor. Add grease motor 25 times-30 times of FS and LS. Check at ER5 and ER4 for RPM-Voltage-Ampere-kW-Temperature motor fill in at check sheet form. Add grease motor for FS and LS for 473 FAA measure noise motor below 2 gE also add grease motor for 473 FA4-FA5-FA6 for FS and LS measure vibration-noise of FS and LS result vibration below 4 mm/s and noise below 2 gE ( AGUS & DADANG )

Cleaning area motor and filter motor. Measure vibration-noise-temperature of FS and LS motor. Add grease motor 15 times-20 times of FS and LS. Check at ER3 and ER4 for RPM-Voltage-Ampere-kW-Temperature motor fill in at check sheet form. Do separated power lighting lamp for 333 BC1 and bel feed test function result normal-Install cover motor for 393 RF4 result function normal- Do adjust position of probe speed sensor result normal error speed failure off( EDI & ADI )

Do test run no load of motor result normal ( AGUS & RIZAL & MUHAIMIN & ANDRI )

Check at ER3, continuity cable and wiring cable of DO at relay at panel I/O test function result ok ( JAJAT & EDI & FIRMAN & DADANG & ADI )

Check at site found finger bar burned, replace cable and pulling cable continue connected cable and terminated ( JAJAT & AGUS & EDI & RIZAL & ADI & ANDRI & MUHAIMIN & DADANG )

Do pulling cable power of heater  and modification contact heater at 443 2K2 result function normal ( AGUS & MUHAIMIN & DADANG )

Do dismantle camera kiln and clean up lens. Reinstall camera kiln result picture available at operator CCR ( JAJAT & RIZAL & ANDRI )

Install  Blower , Monitor  Max 80 Deg celcius - Monitor ( AGUS & MUHAIMIN )

Do PMR CCTV-IR TAD-T scanner-camera burner. Clean up CCTV camera glasses- IR TAD probe glasses- T scanner camera glasses and camera burner probe also glasses from dirty of dust process use equipment cleaning tools and instrument air supply ( AGUS & MUHAIMIN )

Do WBI Elec & Ins & Check I/O GCT, EP,PH&KL. Measure vibration-noise motor and fill at check sheet high vibration motor up to 4 mm/s ( EDI & ADI )

Do WBI Electric & Ins & Check I/O Feed Bin. Clean up area 423 BF1 room from dirty of dust use instrument air supply. Measure vibration-noise motor area 393 FA4-443 WP4,5,6-443 FN1-363 FN1-363 FN2-333 AC1& 333 SX1-333 AC2 & 333 SX2-333 WF1 to WF4-333 BC1-363 SR1-363 CV1 & CV2-363  LQ1 M1 & M2 note area motor dirty of dust  need clean up some motor vibration and noise high ( up to 4 mm/s-up to 2 gE ) ( ADI & DADANG )

Clean up elevator room door and top side-VSD room 8th floor  from dirty of dust use hand blower test function elevator form 8th to 1st floor result normal. Check function of sump pump at L63 HS1-IDO tank-L1C BC1-L1C BC4 note: L63 HS1 need install pipe conduit cable of cable power sump pump- IDO tank need clean up sump pump and install flow siwtch-L1C BC1 & L1C BC4 need clean up area from dirty of wet dust coal make performance sump pump good ( AGUS & ADI )

Prepare material of installation circulation valve LA3 VA4 and install at site result ok Do replace cooling fan of iron sand test function motor  result good ( MUHAIMIN & DADANG & AIMAN )

Clean up purge air unit motor and filter motor. Dust Hunter: clean up flange with tube-swivel window-aligmment TR & R unit. Flowsic 100: transducer A & B. MCS 100 E: filter cabinet. FIDOR: filter cabinet. CEMS room & gas CEMS room: clean area from dirty of dusy use instrument air supply ( RIZAL & ANDRI )

Replace connector LAN for camera test function IP result normal and view camera available at computer CCR ( RIZAL & ANDRI )

Clean up flange probe-probe-filter sample line-sample line tube-diaphragm pump-filter balston from dirty of dust use instrument air supply. Check function humidity sensor and filter humidity result function humidity sensor normal and filter good condition ( RIZAL & ANDRI )

Clean area motor and filter motor. Measure vibration-noise-temperature FS and LS motor add grease motor 25 times and 20 times for FS also LS. Check RPM-Voltage-Ampere-Temperature motor at ER5 and ER4 fill in at check sheet form ( EDI & DADANG )

Clean area motor and filter motor. Measure vibration-noise-temperature FS and LS motor add grease motor 16 times and 15 times for FS also LS. Check RPM-Voltage-Ampere-Temperature motor at ER3 and ER4 fill ini at check sheet form ( EDI & ADI )

Do make reactivation for automatic filling water test function result normal also clean up filter motor compressor and filter sample line from dirty of dust use instrument air supply ( JAJAT & RIZAL & MUHAIMIN & ANDRI )

Replace cable power lighting lamp at 2nd floor at north side and replace lighting lamp  test function lighting lamp result normal  ( EDI & ADI & DADANG )

Check at site found cable motor is not tighten, make tighten cable motor result ampere motor balance note install SOP check problem at motor ( JAJAT & MUHAIMIN & EVE FARAH )

Do make drawing for electrical at 443 2K2 ( AGUS )

Check at site 443 2K1 found there is leakage tube at diaphragm pump to humidity sensor use silicone and isolation electrical to cover leakage of tube ( RIZAL & ANDRI )

Do tighten cable power and output at sensor result indication normal ( JAJAT & MUHAIMIN & EVE FARAH )

Relocation flow sensor for Reference calibration. Repare Cable , Done ( EDI & DADANG )

Modification roof SW at L1C BC4 also repare all safety device area L1C BC1 to L1C BC7 and test function safety device result normal (JAJAT & AGUS & EDI & RIZAL & MUHAIMIN & ANDRI & DADANG )

Do activation lamp  lamp of collective fault  ( MUHAIIN & ANDRI )

Do drawing electrical continue test signal result normal ( AGUS & MUHAIMIN )

Do PMR motor area tripper for L1C BC1-L1C BC2-L1C BC3-L1C BC4-L1C BC5-L1C BC6-L1C BC7 and check TLS note cable gland for probe speed sensor at L1C BC1 & L1C BC3 not connected  action reconnected cable gland result ok-rope of TLS L1C BC4 east side not connected action reconnected rope of TLS-rope TLS north side L1C BC5 not connected action reconnected rope. Also check function of sump pump at L1C BC1 and L1C BC4 result function good ( EDI & ADI )

Measure vibration-noise FS and LS result vibration below 4 mm/s-noise below 2 gE add grease motor 10 times for FS and LS motor ( EDI & ADI & DADANG )

Do make program for off delay 2 second at LOGO for input 1-2-3 ( RIZAL & EVE ILHAM & UNJ AZRIEL )

Do activation proximity level sensor og signal N-M and labelling push button signal 443 2k2-C1-ACK result  ok ( MUHAIMIN & ANDRI )

Redrawing of electrical for 443 2K2 and upload to server manual book ( AGUS )

Do support feeding of 463 KL1 ( AGUS & RIZAL & EDI & ADI & MUHAIMIN & ANDRI & DADANG & EVE ILHAM &UNJ AZRIEL )

Check at location found cable phase and neutral joint, make different connection for cable phase and neutral, test function lighting lamp result normal lighting lamp on note replace MCB 10A ( EDI & ADI & DADANG )

Clean up 363 FA2 area motor and filter motor-area 363 MD1 and CB room from dirty of dust use instrument air supply and equipment cleaning tools. Measure long CB1 47.57-CB2 41.56-CB3 47.82-CB4 39.11-CB5 42.84-CB6 48.13-CB7 40.63-CB8 37.68-CB9 47.24-CB10 41.34-CB11  42.02-CB12 40.28 ( EDI & ADI & DADANG )

Check indication pressure of 423 BF1 PDT 2002 value 2.2 to 2.3 mbar same with CCR operator. Bring down pressure transmitter do zero adjustment result indication become 0.0 mbar output 4.00 mA. Install pressure transmitter at site result indication  0.1 mbar compare CCR around 0.2 mbar-Check at location area sump pump at L63 HS1 found there is no water and sump pump working normal-Do rewiring cable for reset at 443 2K2 continue test function result good also test function for alarm humidity result good-Do calibration zero at 483 PF1 with running blower and calibration zero-span for 453 PF1 with running blower result calibration good ( JAJAT & EDI & ADI & DADANG )

Check indication pressure of 423 BF1 PDT 2002 value 2.2 to 2.3 mbar same with CCR operator. Bring down pressure transmitter do zero adjustment result indication become 0.0 mbar output 4.00 mA. Install pressure transmitter at site result indication  0.1 mbar compare CCR around 0.2 mbar. Check at location area sump pump at L63 HS1 found there is no water and sump pump working normal ( EDI & ADI & DADANG )

Do dismantle motor L63 SX1 bring to workshop repare by mechanic team replace coupling motor ( JAJAT & ADI & MUHAIMIN & DADANG ) 

Replace radar sensor  ( RIZAL & ANDRI )

Make normal of JB 19 no 6 and monitoring. Input addresing new indicator of 443 2K1 and create program ( AGUS & MUHAIMIN & UNJ AZRIEL & DADANG & EVE  ILHAM )

Clean up flange probe-sample line tube-filter sample line-diaphragm pump-filter balston from dirty of coal process. Check function humidity sensor and filter humidity result function humidity normal and filter humidity good condition ( RIZAL & ANDRI )

Do add greasing motor for FS and LS around 10 times and 20 times measure vibration-noise FS & LS: 483 BL9 2.6 mm/s-4.3 mm/s; 1.4 gE-5.02 gE ( EDI & ADI & EVE FARAH )

Do make notification for job rewinding motor shell kiln: 463 FX5B-463 FX6-463 FX8-463 FX10 save at computer ( ADI & MUHAIMIN )

Do reposition camera burner for view fire result view fire available at computer operator ( RIZAL & MUHAIMIN & UNJ AZRIEL & ANDRI )

Clean up area motor and filter motor. Measure vibration-noise-temperature FS and LS motor. Add grease motor for 15 times-20 times for FS and LS motor. Check RPM-Voltage-Ampere motor-Temperature motor at ER4-ER5 write at form check sheet ( AGUS & DADANG )

Clean up area motor and filter motor. Measure vibration-noise-temperature FS and LS motor. Add grease motor for 15 times-10 times for FS and LS motor. Check RPM-Voltage-Ampere motor-Temperature motor at ER3-ER4  write at form check sheet. Clean up area carbon brush room and filter 363 FA2 from dirty of dust use instrument air supply ( EDI & ADI )

Check at site for 463 FX 5B-463 FX6-463 FX8-463 FX10 result motor burned because short ground. Replace breaker result normal ( RIZAL & MUHAIMIN )

Install conduit pipe of cable power, pulling cable power from welding panel inside water pump room to power point. Do wiring cable power ( AGUS & MUHAIMIN & DADANG )

Complete data for assessment report and print out install at TPM board at workshop ( RIZAL )

Check at site for RTD roller coal mill measure resistance result 183 ohm. Rewiring cable RTD at cross check indication at CCR result around 83 degree celcius ( EDI & ADI & UNJ AZRIEL )

Install AUTO Grease motor at 363 FN1-363 FN2-423 FN1-443 FN1-L63 MD1-L63 FN1 ( AGUS & DADANG )

Check at site found bearing motor bad condition, replace motor with spare unit check ampere motor result 10 to 11 ampere ( EDI & MUHAIMIN & ANDRI )

Do clean up area sump from grass-leaf-coal use equipment cleaning tools. Test function sump pump local mode result sump pump work good water come out from tank sump pump Note grass at IDO tank already not tidy, need to tidy up grass  ( ADI & UNJ AZRIEL & EVE ILHAM & EVE FARAH )

Check at site found probe speed sensor failure, replace probe speed use spare unit result speed indication normal ( JAJAT & MUHAIMIN & DADANG )

Cross check indication temperature at cyclone north and south for gas material compare with CCR. Adjust range at local same with indication at local ( RIZAL & ANDRI )

Check actual motor at warehouses find 1 motor but different shaft motor. Continue check at FM warehouses find motor 22 KW and shaft motor 50.1 mm. Dismantle cover motor4 KW at workshop result all bearing failure and bad condition ( EDI & ADI )

Do certification diesel oil at calciner. Repare support travelling probe test function insert and  retract probe result normal  ( RIZAL & UNJ AZRIEL & EVE AJI & ANDRI )

Do prepare Auto Grease tank at workshop ( AGUS & JAJAT )

Clean up area motor and filter motor. Measure vibration-noise-temperature of FS and LS. Add grease motor for 25 times and 30 times for FS and LS motor. Check at ER4 and ER5 for RPM-Voltage-Ampere-Temperature for L63 MD1-L63 FN1-473 FN7-463 MD1  write at check sheet form ( MUHAIMIN & DADANG )

Clean up area motor and filter motor. Measure vibration-noise-temperature of FS and LS. Add grease motor for 15 times and 10 times for FS and LS motor. Check at ER3 and ER4 for RPM-Voltage-Ampere-Temperature for 423 FN1-363 FN1-363 FN2-363 MD1-443 FN1 write at chek sheet form Note area 363 MD1 inside CB room very dirty of dust. Advice clean up employee not  use high pressure near filter 363 FA2 will make easy dirty of dust ( EDI & ADI )

Replace bearing motor, install at location test run motor measure vibration and noise of LS & FS motor result vibration below 4 mm/s and noise below 2 gE ( EDI & JAJAT & MUHAIMIN & DADANG )

Measure vibration-noise-temperature result vibration 5.33 mm/s-noise 5.14 gE-temperature 45 degree celcius ( MUHAIMIN & DADANG )

Check at location found  speed sensor bad condition, replace speed sensor with spare unit rewiring cable test run363 CV2 result normal ( AGUS & EDI & ADI & IMAN )

Do fabrication vessel air tank at workshop  and install vessel tank of air and  s/v water drain at vessel air tank and pulling cable power from welding panel test function water drain result good ( RIZAL & ANDRI )

Take cable power for power point at feed bin bring to location. Install power point panel at L1C BC4 and pulling cable power of power point from welding panel of L1C bC5 to panel power point continue termination at panel note prepare water for make safe area of welding power point ( JAJAT & AGUS & EDI & ADI & MUHAIMIN & DADANG & IMAN )

Do repare support sample line test function insert and retract of probe result good  ( RIZAL & DADANG )

Do dismantle motor at 483 FA2 M1  bring to workshop. Replace  bearing 4 each install motor at site  ( EDI & DADANG )

Do adjust CF at  maximal  note if still needed request adjust do calibration zero and span 453 PF1 ( RIZAL & UNJ AZRIEL )

Install lighting lamp at WP3 WF1 test function lighting lamp result ok ( EDI & DADANG )

Clean up flange probe-sample line-filter sample line-diaphragm pump-filter balston from dirty of coal. Check humidity sensor and sensor humidity result function humidity sensor normal and filter good condition.  Cross check temperature result indication normal note still looking for of phenomenon build material ( RIZAL & ANDRI & UNJ AZRIEL & EVE ILHAM & EVE FARAH )

Check at site. Do make all at normal position solenoid valve result function normal ( MUHAIMIN & DADANG )

Clean up flange probe- probe-filter sample line-sample line-diaphragm pump-filter balston from dirty of dust use instrument air supply. Check humidity sensor and filter humidity result function humidity sensor normal and filter good condition. Replace sensor RTD at 463 KR2 T2 result normal check indication at CCR reading normal( RIZAL & UNJ AZRIEL & ANDRI )

Check Auto Grease motor 493 AC2 and 493 AC3 found low level at tank Auto Grease. Replace Auto grease with spare unit test function result normal. Note environment at 493 AC4 is not good condition and safety because many clinker at floor cover until junction box and cable power. Need action to clean up environment at 493 AC4 ( EDI & ADI )

Install +Connected   Motor , test no load , Commissioning result normal ( MUHAIMIN & ANDRI & DADANG )

Check connection tube of  Hydrogren reset power result flame on. Clean up purge air unit motor and filter purge air unit  of Dust Hunter and Flowsic 100, clean up swivel windows T/R and R dust hunter-flange with tube-alignment dust hunter. Clean up transducer A & transducer B of flowsic, clean up up CEMS room and gas bottle-filter cabinet MCS 100 E from dirty of dust use equipment cleaning tools and instrument air supply (RIZAL & UNJ ASRIEL & EVE FARAH & ANDRI )

Retighten connection of inside camera kiln and outside camera kiln. Insert camera kiln result normal ( MUHAIMIN & DADANG )

Clean up area motor and filter motor, Measure vibration-noise-temperature of FS and LS motor. Add grease motor for 15 times-25 times for FS and LS motor. Also replace battery for AUTO grease motor at 473 FA2-473 FA3-473 FA9-473 FAA-483 FA2 and replace tube of AUTO grease motor at 473 FA6 found tube leakage. Also check 483 BL1-483 BL2-453 BL6-483 BL7 add grease motor for 15 times for FS and LS ( AGUS & ADI & EVE ILHAM )

Do calibration bin shale result good ( EDI & MUHAIMIN & DADANG & TRUBA CEPI )

Complete data check sheet calibration RTD area RM-CC-KL-CM of OH 2026, scan file save at computer and send to Mr.Jajat ( JAJAT & ADI )

Check at site, found motor bad condition.  Dismantle motor bring to work shop. Do clean up motor from dirty of dust and grease also oil ( AGUS & MUHAIMIN )

Install sensor temperature at location cross check indication result normal indication. Dismantle cove motor and drain oil  from motor. Reinstall cover motor test run 393 RF6 result  function normal no oil come inside motor ( EDI & ADI & TRUBA CEPI )

Install sensor temperature at location cross check indication result normal indication. Dismantle cove motor and drain oil  from motor. Reinstall cover motor test run 393 RF6 result  function normal no oil come inside motor ( EDI & ADI & TRUBA CEPI )

Connected cable motor for 393 BE1 - 473 FA6 - 473 FA7 ( MUHAIMIN & CIVACON EMPLOYEE )

Cleaning  PC of operator from dirty of dust use hand blower and vacuum cleaner. Replace S/V for air at gun no 14 issue leakage found existing  S/V membrane not available test function result ok no leakage air. Pulling cable at gun no4 for water because found voltage drop below 220 VAC ( JAJAT & EDI & ADI & TRUBA SUSILO )

Pulling cable RTD for 473 FA3- 473 FA5 and 473 FA6 check indication at CCR result good ( YOGA & DADANG & TRUBA NANANG )

Pulling cable result indication activation I/O result pressure normal indication ( RIZKY & CIVA IRMIS & CIVACON EMPLOYEE )

Reposition slide gate and cleaning ventury cooler ( FAHRI & EVE SUPRIYADI & CIVACON EMPLOYEE )

Replace ampere meter and battery at ER5  test function result good ( AGUS & FIRMAN & AIMAN )

Fabrication of 423 VA2 and install at site test function gate - ML result ok ( RIZKY & CIVACON EMPLOYEE )

Replace cable at 473 FA3 and reinstall sensor RTD at motor result indication normal ( YOGA & DADANG & TRUBA NANANG )

Test  run 473  HC result ok. Connected sensor motor 443 FN1-473 FA6 test run no load 443 FN1 measure vibration and noise LS 7 FS result vibration below 4 mm/s and noise below 2 gE ( HARYANTO & MHAIMIN & CIVACON EMPLOYEE )

Do calibration temperature RTD area Cooler-Kiln-Coal Mill ( EDI & ADI & TRUBA SUSILO )

Do support  black out process at ER3-ER4-ER5 ( JAJAT & AGUS & EDI &  RIZAL & ADI & MUHAIMIN & ANDRI & DADANG & FIRMAN & AIMAN )

Do calibration RTD area RM for 363 FN1-363 FN2; area Cooler: 473 FA1-473 FA2-473 FA-473 FA5-473 FA6-473 FA7-473 FA8 ( EDI & ADI & EVE AJI & UNJ ASRIEL )

Install service motor, alignment motor and connect cable motor ( AGUS & MUHAIMIN & EDI & CIVACON EMPLOYEE 7 PEOPLE & EVE SONY & TRUBA SUSILO & TRUBA NANANG )

Do replace TU 17 units at east blending and 5 units at west blending. Clean up area panel I/O use hand blower from dirty of dust ( JAJAT & PENY & ADI & EVE SONIY & FIRMAN &  CIVA HERMAN )

Do complete data check sheet calibration pressure transmitter  OH Nr1 and continue scan file send to Mr. Jajat ( JAJAT & ADI )

Recheck connection cable power at 473 FN7 and clean up area motor add silicone at panel cable motor. Inspection electrical and welding tools of PT Jantan Setia Sakti and PT Bintang Eka Sakti note 1 welding machine rejected because ground cable not connected. Tagging equipment with green color ( EDI & TRUBA SUSILO & TRUBA NANANG )

Calibration pressure transmitter area cooler for zero and span ( ADI & EVE SUPRIYADI & EVE ZAHRA )

Inspection electrical tools of Mechanic 1-Pincuran Mas-Plant Building tagging equipment with green color ( EDI & TRUBA SUSILO & TRUBA NANANG )

Calibration pressure transmitter for zero and span area Cooler-CM for 7 units note replace 2 transmitter because output mA not stable and output pressure not stable also replace resistance 200 ohm found bad condition ( ADI & EVE SUPRIYADI )

Support black out process at ER3 and ER4. Clean up trafo-VCB-VCS and DS from dirty of dust use hand blower and vacuum machine. Measure MV  at trafo ( JAJAT & AGUS & EDI & RIZAL & ADI & MUHAIMIN & ANDRI & DADANG & TRUBA SUSILO & TRUBA NANANG )

Calibration pressure transmitter for zero and span area cooler and pre heater Note: replace 1 pressure transmitter with spare unit because leakage pressure indication and output mA too big ( ADI & EVE SUPRIYADI & EVE ZAHRA )

Inspection electrical and welding tools of PT MBL - PT Truba Jaga Cita - PT Indoporlen Tagging equipment with green color ( JAJAT & ADI )

Calibration pressure transmitter area cooler-pre heater- coal mill total 14 units for zero and span ( ADI & EVE AJI & EVE SUPRIYADI & EVE ZAHRA & UNJ ASRIEL )

Inspection electrical and welding tools of PT Quadro tagging equipment with green color ( EDI & TRUBA SUSILO & TRUBA NANANG )

Inspection electrical and welding tools of PT Quadro-PT MBL- PT BMC note repare cable connection vacuum pump because existing joint cable to single cable. Tagging equipment with green color ( EDI & ADI & TRUBA SUSILO & TRUBA NANANG )

Inspection electrical and welding tools of PT MBL- PT RMP note 1 cutting machine rejected because breaker not install and ground cable is not connected- PT Jantan Setia Sakti note 1 grinding machine rejected because start-stop is not function. All equipment tagging green color ( EDI & ADI & TRUBA SUSILO & TRUBA NANANG )

Do inspection electrical and welding tools PT MBL-ADZALAMA-RMP_INDOPORLEN tagging green color note 2 cutting machine  RMP rejected because ground cable are not connected,  1 extention cable MBL rejected because  not full fill safety requirement SBI ( ADI 7 TRUBA SUSILO & TRUBA NANANG

Do install 1 lighting lamp test function lighting lamp result normal ( RIZAL & ANDRI )

Replace O2 sensor test function sensor O2 with calibration zero and span result normal ( RIZAL & ANDRI )

Dismantle motor from site bring to work shop. Do replace bearing motor and installation motor at site ( AGUS & MUHAIMIN & DADANG )

Do inspection electrical and welding tools of PT Jantan Setia Sakti tagging equipment green color. Inspection electrical and welding tools of Electrical Nr1 tagging equipment green color note repare 1 extention cable because ground cable is not connected ( ADI & TRUBA SUSILO & TRUBA NANANG )

Discouple motor test run no load result high noise up 2 gE note need replace bearing motor ( JAJAT & AGUS & MUHAIMIN )

Do Install lighting lamp tend OH  test function result lighting lamp on ( AGUS & MUHAIMIN & RIZAL & ANDRI & DADANG & EVE AJI )

Inspection electrical tools of PT Supra and tagging equipment with green color. Inspection welding tools of PT Truba Jaga Cita for 21 units tagging green color. Inspection electrical and welding tools of Electrical 1 tagging green color ( EDI & ADI & TRUBA SUSILO 7 TRUBA NANANG )

Do complete data TPM ER3 safe at computer and print out ( JAJAT & RIZAL )

Fabrication and install new lighting lamp area 443 PH1 & 473 CC1   test function lighting lamp result good ( AGUS & MUHAIMIN & DADANG )

Inspection electrical and welding tools of AFR work shop tagging green color. Inspection electrical tools of Total Prime Engineering note repare ground cable at extention cable because cable is not connected tagging equipment green color ( ADI & TRUBA SUSILO & TRUBA NANANG )

Fabrication and install new lighting lamp area PH and CM  test function lighting lamp result good ( AGUS & MUHAIMIN & DADANG )

Do support calibration for flow meter diesel result normal ( RIZAL & ANDRI & AIMAN )

Inspection electrical and welding tools of mechanic II. Tagging green color note: repare connection cable at extention cable and welding cable. 1 portable lamp and 1 welding machine are not full fill safety requirement of plant. Inspection welding tool of PT Truba Jaga Cita tagging green color. Inspection electrical and welding tools of CBM note repare portable lamp ground cable connection and  cover of lamp tagging green color ( EDI & ADI & TRUBA SUSILO & TRUBA NANAG )

Replace filter result monitoring still not good performance camera still stuck ( RIZAL & EVE AJI & ANDRI )

Check inspection tools of MEGA VOLT PERKASA, tagging with green color. Mechanic work shop Nr2 inspection electrical tools and welding tools tagging green color, note repare female connector of welding machine and cable welding minus and cable welding plus (continue) ( EDI & ADI & TRUBA ANIS & TRUBA AZIZ )

Clean up flange probe-probe-filter sample line-sample line-diaphragm pump-filter balston from dirty of dust use instrument air supply. Check function of humidity sensor and filter humidity result function humidity sensor normal and filter humidity good condition ( RIZAL & EVE AJI & ANDRI )

Clean up area motor and filter motor from dirty of dust use instrument air supply. Measure vibration-noise-temperature of FS and LS also add grease motor of FS and LS for 25 times-30 times. Write KW-Voltage-Ampere-Temperature of motor at ER5 & ER4. Add grease for 333 BC1 issue high vibration up 4 mm/s and high noise up 2 gE ( MUHAIMIN & DADANG )

Clean up area motor and filter motor from dirty of dust use instrument air supply. Also clean up filter 363 FA2 M1 from dirty of dust use instrument air supply. Measure vibration-noise-temperature of FS and LS also add grease motor of FS and LS for 15 times-25 times-30 times. Write KW-Voltage-Ampere-Temperature of motor at ER3 & ER4 ( EDI & ADI )

Do activation power point near WF limestone. Pulling cable power and continue tagging labelling of W83 WF1 ( AGUS & MUHAIMIN & DADANG )

Clean up flange probe-sample line-filter sample line-diaphragm pump-filter balston from dirty of dust coal use instrument air supply. Check function of humidity sensor and filter humidity result function humidity sensor normal and filter good condition ( RIZAL & ANDRI )

Go to site found there is no slink available at site. Install slink spare together with nut  test  function slink result normal ( EDI & ADI )

Clean up area ware house of ER5 use vacuum cleaner and equipment cleaning tools ( JAJAT & AIMAN )

Do clean up area inside ER3 at bottom side use equipment cleaning tools. also  clean stair beside ER3. Move ex MCS 100E to ER3 top floor ( JAJAT & AGUS & EDI & RIZAL & ADI & ANDRI & MUHAIMIN & DADANG )

Prepare power point ( RIZAL & EVE AJI & ANDRI )

Prepare  welding point ( AGUS & MUHAIMIN )

Do clean up purge air unit motor and filter purge air unit-flange with tube of dust hunter-swivel window T/R + R unit-alignment dust hunter-transducer A+B flowsic 100+CEMS room-CEMS gas room-filter cabinet MCS 100E from dirty of dust use instrument air supply ( RIZAL & EVE AJI & ANDRI )

Do inspection electrical and welding tools of PPUP work shop. Tagging equipment with green color ( EDI & DADANG )

Fabrication panel of welding outside L1C RE1, install at location ( AGUS & MUHAIMIN & DADANG )

Complete data check sheet for PMR analyzer L63 2K1-L63 2K2-L63 @K3-483 2K1-463 2K1-443 2K1-423 2K1-PMR CCTV-Temperature IR TAD-T scanner-Camera Burner-PMR critical motor 363 RM1-443 Ph1-L63 RM1-473 CC1-463 KL1, WBI Elec & Inst Top Blending-CT-PH-KL, WBI Elec & Inst Feed Bin-RM-CT-Dust Transport-BF, WBI Elect & Inst CM-Truck Lift-BC Transport-Reclaimer Coal for month of April 2026 ( ADI )

Replace S/V no 4 & 14 test function S/V normal. Check at location of motor result bad condition. Note replace motor with spare unit ( RIZAL & ANDRI )

Filter Sika Saturated, replace part  (Monitor ) Oke ( FIRMAN & RIZAL & DADANG )

Power  Bank 3 trip, check Solenoid VK  (No 16) short, Replace Part test from DO Jump (Normal) , Mitigasi 1 fuse - 1 solenoid (JAJAT & RIZAL )

 Support take and mobilization and document recondition motor 2400 KW to REMS ( AGUS & ANDRI & AIMAN )

Clean up flange probe-filter sample line-sample line-diaphragm pump-filter balston from dirty of dust use instrument air supply. Check function humidity sensor and filter humidity result function humidity sensor normal and filter good condition ( RIZAL & DADANG )

Pulling  cable  Control to  IO -LCS (6P x 1,5 mmx 4), Pulling cable control Power,  fabrication and install Control Panel, Prepare connecting  Control Side and IO side , fabrication and install  Ladder cable and LCS panel ( JAJAT & AGUS & EDI & ADI & MUHAIMIN & DADANG )

Dismalting nut broken, Replace part  broken, setting gap,commisioning  (Normal) ( EDI & MUHAIMIN & ANDRI & DADANG )

Cleaning  Motor , cek Vibrasi/Temp   Motor Fill in Greate tube 363-FN1 /FN2.  Cleaning  Motor , cek Vibrasi/Temp   Motor ( AGUS & RIZAL & EVE AJI )

Do  continue fabrication cable ladder of ER6 and cover tunnel. Install cable ladder and cover tunnel at ER6 ( MUHAIMIN & ANDRI & DADANG )

Check at location there is no voltage 220 VAC, make jumper resistor for no 13-14, Note replace relay K-7 contact temperature  for 13-14 to make function normal. Painting cover motor with yellow color continue install for cover motor 4D3 SC4 at location ( JAJAT & RIZAL & EDI & ADI & AIMAN )

Do painting area motor at CKD with yellow color ( JAJAT & AIMAN )

Clean up flange probe-sample line-filter sample-diaphragm pump-filter balston from dirty of dust process use instrument air supply. Check function of humidity sensor and filter humidity result function humidity sensor normal and filter humidity good condition ( RIZAL & EVE AJI )

Do wiring control panel W83 WF1 and make hole for exhaust fan panel. Install panel of power point at 443 FN1 ( AGUS & MUHAIMIN )

Do complete data check sheet WBI grounding-arrester also make folder for WBI Electrical and Instrumentation Check I/O Sump pump Blending-Cooler-Coal Mill-Kiln ( JAJAT & ADI )

Do conplete data check sheet PMR analyzer-PMR hoist crane-PMR IR TAD-T scanner-CCTV-Camera burner-PMR critical motor Note make check sheet folder for WBI Elec & Inst & Check I/O & S. Pump Blending-Cooler-CM-Kiln also print out data check sheet ( JAJAT & ADI )

Do wiring control WF of FABA ( AGUS & MUHAIMIN )

Replace bearing motor with use heater bearing. Install motor at site. Test function motor , measure vibration and noise motor result  vibration below 4 mm/s and noise below 2 gE ( AGUS & MUHAIMIN & ANDRI & DADANG & JAJAT & RIZAL )

Clean up flange probe-probe-filter sample line-sample line-diaphragm pump-filter balston from dirty of dust process use instrument air supply. Check function humidity sensor and filter humidity result function humidity normal and filer humidity good condition ( RIZAL )

Do inspection electrical and welding tools of PT Truba Jaga Cita tagging with green color. Note 3 extention cable are rejected because not  full fill requirement safety of plant total equipment electrical 18 units and welding 5 units ( EDI & ADI )

Clean up area motor and filter motor. Measure vibration-noise-temperature of FS and LS motor. Add grease for 20 times AND 25  times for FS and LS. Write KW-Ampere-Voltage at ER3 put at form check sheet ( MUHAIMIN & DADANG & EVE AJI )

Clean up area motor and filter motor. Measure vibration-noise-temperature FS and LS motor. Write KW-Voltage-Ampere at ER4 & ER5 put at form check sheet. Add grease 25 times and 30 times for FS and LS ( AGUS & ANDRI )

Check electrical tool of PT Pincuran Mas tagging with green color. Note repare connection extention cable and portable lamp ( EDI & ADI )

Relocation 2 panel I/O  station 21 & 31 from south side to north side of 333 WF5 also move power lighting lamp to  panel I/O west side of 333 WF5. Pulling cable for power VS and power control. Prepare control and test partial like function speed and LC ( JAJAT & AGUS & EDI & RIZAL & ADI & MUHAIMIN & ANDRI & AIMAN )

Clean flange probe-sample line-filter sample line-diaphragm pump-filter balston from dirty of coal . Check function humidity sensor and filter humidity result function humidity sensor normal and filter good condition ( RIZAL & EVE CINDA & ANDRI )

DO clean up ER room and MCC panel also filter panel form dirty of dust use equipment cleaning tools. Also do vacuum room use vacuum cleaner also mop room ( AIMAN )

Prepare upgrade control WF FABA Do make report upgrade recondition motor( AGUS & MUHAIMIN )

Inspection electrical tools of Civil Building. Do repare connection portable lamp 2 each test run nomai, repare 1 each extention cable test run normal Note total equipment 25  tools tagging with green color ( EDI & ADI )

Do repainting  7 cover yellow color  motor at CKD area ( ANDRI )

Do fabrication panel for upgrade WF of  FABA ( AGUS & MUHAIMIN )

Replace sump pump motor with spare unit, test function result sump pump still working abnormal suspected many coal inside water ( EDI & ADI )

Replace sump pump motor with spare unit, test function result sump pump still working abnormal suspected many coal inside water ( EDI & ADI )

Clean up area Electric Room 4 bottom and top also MCC  panel and filter panel from dirty of dust use equipment cleaning tools and vacuum cleaner. Continue mop floor electric room top and bottom (AIMAN )

Do complete data form of recondition motor from SBI and vendor and write bearing support of motor ( MUHAIMIN )

Do clean up panel control L1C  TR1- Radio Link and  L3C RE1 from dirty of dust coal use instrument air supply also clean up safety device-lighting lamp-LCS motor-panel welding from dirty of coal dust ( JAJAT & EDI & ADI )

Clean up flange probe-sample line tube-filter sample line-diaphragm pump-filter balston from dirty of coal use instrument air supply. Check function of humidity sensor and check filter humidity result function humidity sensor normal and filter humidity good condition ( RIZAL & ANDRI )

Install blower, Cleaning  Filter 363 FA2 (Monitor temperature T6 = 114 deg) ( MUHAIMIN & ANDRI )

Take control at Mr.Yunus bring to workshop. Prepare control FABA at workshop ( AGUS & MUHAIMIN )

Clean up flange probe-probe-filter sample-sample line-diaphragm pump-filter balston from dirty of dust. Check function humidity sensor and filter humidity result function humidity normal and filter good condition ( RIZAL & ANDRI )

Do WBI Elec & Ins & Check I/O & S Pump Bl,C Area Kiln. Do test function sump at IDO tank result function normal-L1C BC4 result can not start from LCS because manual function do clean up motor sump pump at workshop found much dirty of coal test function motor sump pump result normal take screning motor sump pump install at motor continue install location test function normal function-L1C BC1 result functon normal. Clean I/O panel area cooler and blending west and east-kiln from dirty of dust use equipment cleaning tools ( EDI & ADI )

Power VSD 333 WF5 take from W83 RF3 and for WP3 RF3 take from distribution power ( JAJAT & AGUS & MUHAIMIN )

 Check at local found stick limit switch broken, replace stick result monitor T scanner normal ( RIZAL & ANDRI )

Check LCS result normal, check I/o module result abnormal, change address signal S test start result function motor normal ( JAJAT & MUHAIMIN & ADI )

Go to location measure motor at CKD for make cover motor. Do fabrication cover motor area CKD at workshop. Install 4 cover motor at site of CKD ( ANDRI & WIKAN )

Clean up purge air motor and filter motor-swivel windows T/R, R unit  also flange with tube of Dust Hunter also alignment Dust Hunter-transducer A & B of Flowsic-CEMS room-filter cabinet MCS 100 E-CEMS gas room from dirty of dust use instrument air supply. Replace H2 bottle for FIDOR continue calibration zero and span result normal ( RIZAL & EVE CINDA )

Clean up area motor and filter motor from dirty of dust use instrument air supply. Measure vibration-noise-temperature FS and LS motor also grease motor for 20 times - 25 times for FS and LS motor. Write ampere-KW-voltage-temperature motor at ER4 & ER5 continue write at check sheet ( AGUS & MUHAIMIN )

Clean up area motor, filter motor from dirty of dust use instrument air supply. Measure vibration-noise-temperature of FS and LS motor. Add grease motor for 15 times and 20 times for FS and LS motor, Write ampere-KW-temperature-voltage motor at ER3 and ER4 continue write at check sheet note Carbon Brush no8 at 363 MD1 -1 need to replace with spare unit ( EDI & ADI )

Clean up ER5 top and bottom  made report Feb-March 2026 also do clean up 423 2K1 room analyzer ( AIMAN )

Cleaning Motor  493-AC1, AC2 ,AC3 also add grease motor ( ANDRI & DADANG )

Cleaning All Door elevator test function elevator result normal note AC control elevator failure and push button inside elevator bad condition ( AGUS &  MUHAIMIN )

Set HRG to 75% do monitor result normal function ( JAJAT )

Do observation relocation station of area WF, check cable needed approximately cable needed enough if station move to 333 WF1. Also check cable at warehouse for 4 x 25 mm result cable are not available ( JAJAT & EDI & ADI )

Cleaning Sensor Level,   set to overflow do monitor setting 75% ( ADI & MUHAIMIN & ANDRI )

Do prepare panel power point at work shop for 2 panel including wiring inside panel ( AGUS & DADANG )

Check at location found tank grease bad condition make grease motor outside tank, replace tank of grease pump result grease motor function normal ( EDI & DADANG )

Do clean up flange probe-sample line-filter sample line-diaphragm pump-filter balston-check function humidity sensor and filter humidity from dirty of coal result function humidity sensor normal and filter good condition note replace filter sample line for L63 2K2 with spare unit. Clean up flange probe-probe-filter sample line-sample line tube-diaphragm pump-filter balston from dirty of dust also check function of humidity sensor and filter humidity result function sensor humidity normal and filter humidity normal ( AGUS & MUHAIMIN & ANDRI )

Do WBI WBI Switchgear, Capacitor & Trafo RM, KL & CM1, write result at form ( EDI & DADANG )

Do complete data check sheet for WBI Elec & Ins & Check I/O GCT, EP,PH&KL and PMR CCTV, IR TAD & Kiln Scanner NAR1 for date 23/3/26 and 24/3/26 at form also make report of SOT of march month  ( ADI & JAJAT )

Do fabrication support of panel power point at workshop ( ADI & ANDRI & DADANG )

Do clean up area motor and filter motor. Measure vibration & noise motor of FS and LS. Add grease 25 times-30 times- 15 times for FS and LS ( RIZAL & DADANG )

Do complete data check sheet PMR analyzer L63 2K1-:63 2K2-L63 2K3-483 2K1-463 2K1-443 2K1-423 2K1, PMR IR TAD-CCTV-T Scanner-Pyrometer, Critical motor 363 MD1-363 FN1-363 FN2-423 FN1-443 FN1-L63 MD1-L63 FN1-473 FN7-463 MD1-WBI Top blending-CT-PH-Kiln WBI Bottom Blending-Kiln-Cooler-Clinker Silo WBI CM-Truck Lift-Tripper-Reclaimer Coal and print out data check sheet 9 to 12 copies ( ADI )

Do make hole of power cable panel welding continue connected at panel welding, test output result ok ( AGUS & DADANG )

Do connect cable power point of 363 MD1 at panel welding bottom cyclone raw mill test on measure output result normal ( EDI & ADI )

Clean  up area motor 363 MD1 and carbon brush room from dirty of dust also clean 363 FA2 filter motor from dirty of dust use instrument air supply. Check long carbon brush found no 8 is to short replace carbon brush no 8 with spare unit ( EDI & ADI )

 Replace fuse-install filter and UV lamp. Do replace-modification LS, result T scanner result view T scanner at operator normal. Replace RTD, tidy up cable result cooling system normal at analyzer 463 2K1  ( RIZAL & ANDRI )

Do finishing wiring panel of upgrade control also put name of indication at front of panel ( AGUS & MUHAIMIN )

Install pipe 2 inch for cable route from h-beam raw mill. Puling cable from welding cyclone raw mill to location power point at 363 MD1 also connected cable ( EDI & ADI & DADANG )

 Replace pressure transmitter  and setting parameter 130 mmH2O result indication draft back to normal at CCR operator. Fabrication support of pressure transmitter. Note  Beck actuator function normal but at blade mechanical not response  (RIZAL & EVE CINDA & ANDRI )

Continue wiring cable inside panel  of upgrade panel 443 2K1 ( AGUS & MUHAIMIN )

Do replace proximity for gate because existing signal error at CCR operator result after function normal ( RIZAL & ANDRI )

Continue wiring cable inside panel and install panel upgrade inside analyzer 443 2K1 room ( AGUS & MUHAIMIN )

Do clean up analyzer 443 2K1, and repainting floor with green color and door with yellow color ( JAJAT & AIMAN )

Do clean up filter sample-flange probe-sample line-diaphragm pump-balston filter from dirty of coal use instrument air supply. Check function humidity sensor  and filter humidity result function humidity sensor normal and filter humidity good condition ( RIZAL & ANDRI )

Clean Filter unit both of 363 FN1 and 363 FN2 result alarm temperature disappear ( EDI & DADANG )

Continue do wiring panel of upgrade analyzer 443 2K1 ( AGUS & MUHAIMIN )

Clean up purge air unit motor and filter motor- flange with tube Dust Hunter-swivel windows of T/R also R-alignment Dust Hunter- transducer A & transducer B of Flowsic- CEMS room also filter cabinet MCS 100 E-CEMS gas room bottle form dirty of dust use instrument air supply ( RIZAL & ANDRI )

Add grease motor around 20 times for FS & LS also add grease motor 483 BL7 for LS 10 times and FS 8 times ( EDI & ADI )

Check at location, found lighting lamp off and cable power for lighting lamp is not connected to cable power input. Do reconnected cable power result lighting lamp normal operation ( EDI & ADI & DADANG )

Do revision drawing of upgrade control analyzer 443 2K1 and print out file drawing of upgrade control analyzer 443 2K1 ( AGUS & MUHAIMIN )

Clean up flange probe-probe-sample line-diaphragm pump-filter balston from dirty of dust process. Check function of humidity sensor and filter humidity result function sensor normal and filter humidity good condition. Note replace filter sika at analyzer 463 2K1 and do calibration zero gas and span gas result calibration ok( RIZAL & EVE CINDA & ANDRI )

Clean up area motor-filter motor from dirty of dust use instrument air supply. Measure vibration-noise-temperature for FS and LS motor. Add grease from 25 times-30 times for FS and LS. Write  RPM-Voltage-Ampere-Temperature motor and bearing at electric room 4 and electric room 5 ( MUHAIMIN & DADANG )

Clean up area motor-filter motor from dirty of dust use instrument air supply. Measure vibration-noise-temperature for FS and LS motor. Add grease from 15 times-20 times-30 times for FS and LS. Write RPM-Voltage-Ampere-Temperature motor and bearing at electric room 3 and electric room 4 Note there alarm at 363 FN1 because temperature 112 degree C at MICOM ( EDI & ADI )

Wiring  Control Local  ( AGUS & MUHAIMIN )

Replace diaphragm L63 BF1 ( RIZAL & ANDRI & DADANG )

Repare and Cleaning result ok ( RIZAL & ANDRI & DADANG )

Do PMR load MCC and UPS at ER3-ER4-ER5-ER6 ( EDI & ADI )

Check at location, replace contact kit BD 5 of 433 BE1. Do replace pump of dryer gas at 443 2K1, monitor reading O2 and CO2 for probe 1 and probe 2 result reading gas of O2 and CO normal as process ( RIZAL & EVE CINDA & ANDRI )

Check 393 SC5 at location, do clean up probe of motion test simulation  result normal indication signal S and speed monitor ok at CCR operator ( EDI & DADANG )

Do wiring cable power of lighting lamp 6 units, test result lighting lamp normal ( JAJAT & ADI )

Do support heating up process and feeding kiln ( JAJAT & ADUS & RIZAL & EDI & ADI & MUHAIMIN & ANDRI & DADANG )

Numbering File-File at file box and name file at panel ( JAJAT & ADI )

Repare-Welding join piping, create valve drain  pressure pump leaked, repared, normal ( RIZAL & ANDRI )

Dismantling Panel Ex-Sick and LR ( EDI & EVE CINDA & DADANG )

Tapping Power From welding point transport 423-F1 ( EDI & DADANG )

Check at location, do clean up load cell result indication level normal ( RIZAL & MUHAIMIN & EVE CINDA )

Do calibration flow diesel with drop test result  good ( RIZAL & MUHAIMIN & EVE CINTA )

Do prepare CT at workshop 50/5A, and wiring cable for CT at workshop and install CT 50/5A at ER3 for 383  SC8 and wiring cable output at panel I/O at ER3 result indication ampere normal ( JAJAT % EDI & ADI & DADANG )

Do fabrication cover of motor 393 BE1 -433 BE1 and install at location ( EDI & MUHAIMIN & DADANG )

Check at location found cable power is not long enough, also measure resistance cable found bad result. Replace connector cable power motor with spare result motor shell cooling fan function normal ( EDI & MUHAIMIN & DADANG )

Complete data file for calibration RTD year 2025, PMR Service Analyzer-PMR IR TAD-CCTV-Tscanner-Camera Burner-PMR Critical Motor of 363 RM1-443 PH1-L63 RM1-473 FN7-463 KL1-PMR Clean Electric Room of 3-4-5-6 for year 2025 and 2026 and print out data PMR clean up ER3-ER4-ER5-ER6 ( JAJAT & ADI )

Do install sign safety for assembly point 2 each outside ER6-Evacuation Route 4 each inside ER6-Equipment cleaning tools 2 each inside ER6. Accompany assessment at dash board TPM ER6 at work shop ( RIZAL & ADI & AIMAN )

Do reposition of level sensor and rewiring cable sensor also data, result level same with operator CCR expected ( RIZAL & ANDRI )

Do dismantle level sensor and clean up sensor reinstall level sensor result indication available at CCR ( RIZAL & MUHAIMIN & EVE CINTA & ANDRI )

Do prepare report of TPM ER6, print out sign Catatan GEMBA  5R and VOM get sign from Mr.Jajat, Mr. Heri Setiawan and Mr. Safrin and put at dashboard TPM at work shop ( JAJAT & RIZAL & ADI )

Add grease motor at L63 MD1 measure noise result below2 gE. Do add grease motor of 20 KW measure vibration and noise result normal vibration below 4 mm/s and noise below 2 gE ( AGUS )

Clean up purge air unit motor and filter motor, swivel window of Dust Hunter do alignment Dust Hunter, transducer A and transducer B of Flowsick, CEMS room gas bottle area, CEMS room. filter cabinet MCS 100 E from dirty of dust process use instrument air supply ( RIZAL & MUHAIMIN & ANDRI )

Clean up filter sample-sample line-diaphragm pump-filter balston from dirty of coal. Check function humidity sensor and filter humidity result function humidity normal and filter sensor good condition ( EDI & EVE CINTA & DADANG )

Install Blower 2 side result temperature normal at CCR operator ( EDI & AGUS )

Do prepare report TPM ( RIZAL )

Monitor, team Karteksi repare piping Leaked, Add Gas Freon result AC function normal and temperature normal ( JAJAT & AGUS )